Model
182C
Changee
and Options
SECTION VII
MANUAL
CHANGES AND OPTIONS
7-1. INTRODUCTION.
7-2.
This section contains
information required
to
back-
date or update this manual
for
a
specific instrument.
Descriptions of special options and standard options
are also in this section.
7 3. MANUAL
CHANGES.
7-4. This manual
applies directly to the instrument
having a serial
prefix
as
shown on the manual
title
page.
If the serial
prefix of
the
instrument is not the
same as
the one on the title page,
refer toTable
7-1
for
changes necessary to
backdate the manual to the
instru-
ment.
When making changes from
Table
7-1, make
the
change with the
highest number first.
Table 7-1. Manual Changes
Serial Prefix
Make Changes
1240A, 1241A
3
thru 1
1248A
Sand 2
131 1A
3
CHANGE 1
Table
6-2,
A1
(on pages
6*2
and
6-51:
Change
HP and Mfr. Part
No. to
00182-60018.
A1T1: Change HP and Mfr. Part Nos. to
9100-1129.
A1 A1 : Change
HP and Mfr. Part Nos. to
00182-66505.
A1A1C1;
Change
to
HP Part No.
0180-1811;
C;
FXD ELECT 100
UF
+75V -10%
VDCW; Mfr.
Code 56289;
Mfr. Part No. 600D107G0200D4.
A1A1CR1 through A1A1CR4;
Change to HP Part
No. 1909-0049:
DIODE: SILICON 50
PIV Mfr.
Code 28480;
Mfr. Part No.
1901-0049.
A1A1R3: Delete.
A1A1R4; Delete.
A1A1VR1; Delete.
A1A2:
Change HP and Mfr. Part Nos. to
00182-66514.
A1A2C1:
Change
to
HP Part No.
0160-2204;
C:
FXD
MICA
100
PF 5%
Mfr.
Code 72136;
Mfr.
Part No.
RDM 15F10U3C.
A1A2Q1:
Change to HP Part No.
1854-0039; TSTR:
SI NPN; Mfr. Code 80131:
Mfr. Part No. 2N3053.
A7CR1
through A7CR3:
Change
to
HP Part No.
1901-0535; DIODE; HOT CARRIER;
Mfr.
Code
28480; Mfr. Part No.
1901-0535.
Page 7-4, Table
7-2,
Option
807 Replaceable Parts.
A5: Delete.
Page 8-12. Figure
8-6;
Delete. Replace with Figure 7-6.
Page 8-14, Figure
8-7:
Delete. Replace with
Figure
7-7.
Page 8-15,
Figure
8-8;
Delete. Repriace with Figure
7-8.
CHANGE 2
Table 6-2,
A5 (on pages
6-2 and 6-10): Change HP and Mfr. Part
No. to 00182-60003.
A5A1: Change HP
and Mfr. Part No. to 00182-66510.
Table
7-2,
Add; AS,
00182-66518, Assy: horizontal
amplifier
module.
A8:
Change HP and Mfr. Part No. to 00180
66548,
Board assy:
auxiliary.
Delete: A8C1.
CHANGE 3
Table 6-2,
Delete; A2C7
Page 8-23, Figure
8-16,
Delete: A2C7.
7-5.
SPECIAL OPTIONS.
7>6.
Most
customer special application requirements
and/or specifications can be met by
factory modification
of a standard instrument. A standard
instrument modified
in this way will
carry
a special
option number,
such as
Model OOOOA/Option
C01.
7-7.
An
operating and service manual and
a
manual
insert
are provided with each special option instru-
ment. The
operating and service manual contains informa-
tion about the standard
instrument.
The manual insert
for The special option describes the factory modifications
required
to
produce the special option instrument. Amend
the operating and
service
manual by
changing
it to
include
all manual insert information. When these changes are
made, the operating and service
manual
will apply to the
special option instrument.
7-8. If
you
have ordered
a
special option instrument
and
the manual
insert is missing, notify
the
nearest
Hewlett-Packard Sales/Service Office, Be sure to give
a
full description of the instrument, including the complete
serial number and special option number.
7-9. STANDARD OPTIONS.
7-10. Standard options are modifications installed on
HP instruments
at
the factory and are available on re-
quest. Contact the
nearest Hewlett-Packard Sales/Service
Office
for
information concerning standard options.
7-11.
Table
7-2
lists the available options for
the
Model
182C.
7-1
To Next Page
Loading...
