HP 182C - Table; Replaceable

Changes and Options
Table
7-2.
Model 182C Options
Model
182C
DESCRIPTION
230-Vac operation set at factory.
Standard CRT (VI) is replaced by P2 phosphor CRT, HP Part No. 5083-3922.
Instrument is set at
factory for operation from power
source
of
100 or 200 Vac ±10%, 48 to 440
Hz, 200 VA maximum. Make the
following
changes to Table 6-2, Replaceable Parts,
for
Option
003:
A1
: Change HP and Mfr. Part Nos. to
00182-60014.
A1T1 ;
Change HP and Mfr. Part Nos. to 9100-3249.
MP29:
Change HP and Mfr. Part Nos. to 00182-00217.
Standard CRT (VI) is replaced by P7 phosphor CRT, HP
Part
No.
5083-3932.
Oscilloscope
mainframe without rear panel MAI N GATE OUTPUT, DELAYED GATE OUTPUT,
DELAYED SWEEP OUTPUT, or
MAIN
SWEEP
OUTPUT connectors. Make
the
following
changes
to Table 6-2,
Replaceable Parts, for Option 010:
A3: Change
HP
Part No. to
00182-60020.
A3MP2: Delete.
A3W2:
Delete.
A8:
Delete.
J2-J5: Delete.
W3:
Change HP Part No. to
00182-61611.
Add: RESISTOR, FXD MET FLM 51101% 1/8W, HP Part No. 0757
0438,
to replace
A8R15
on schematic
4.
Add: TERMINAL BOARD, HP
Part
No.
0360-0013
to support added resistor.
Standard CRT (VI) is replaced by P1
1
phosphor
CRT.
HP
Part
No. 5083-3942.
The intensification
function of the FIND BEAM switch is deleted on Option 01 1 instruments equipped with PI
1
phosphor
CRT to eliminate phosphor
burn. Figure
7-1
shows the change
to
the
schematic
for
the
Control Module, A2. Figure
7-2
illustrates the location
of
the jumper wire to be removed. If the
CRT is replaced with a standard P31 phosphor CRT, the FIND BEAM intensification capability
may be
restored
by
replacing the jumper wire.
Instrument Is set at factory for operation from power source
of
100 or 200 Vac ±10%. 48 to 440
Hz. 200 VA
maximum. Oscilloscope mainframe Is supplied without rear panel MAIN
GATE
OUTPUT, DELAYED GATE
OUTPUT, DELAYED SWEEP OUTPUT, or
MAIN SWEEP OUT-
PUT connectors. Make the
following
changes to table
6-2, Replaceable Parts, for
Option 013:
A1 :
Change
HP and
Mfr
Part Nos. to 00182 60014
(pages
6 2 and 6 5).
A3: Change
HP
and
Mfr Part
Nos. to
00182-60020
(pages
6-2
and
6-9).
Delete:
A8
(pages
6-2
and 6-1B).
Delete: J2 through J5.
MP29: Change HP and
Mfr
Pan Nos. to
00182-00218.
Add: MP29R1, HP Pan No. 0757-0438. R; FXD MET FLM 51
10
OHM
1% 1/8W,
Mfr Code
28480,
Mfr
Pan No.
0757-0438
to
replace
A8R15
on schematic
4,
Add:
MP29MP1,HPPartNo.
0360-0013,
TERMINAL
BOARD.
Mfr Code
28480,
Mfr
Part
No. 0360 0013 to
support MP29R1.
W3: Change
HP
and
Mfr Part
Nos. to
00182-6161
1
.
A1T1; Change HP and
Mfr
Part Nos. to
9100-3249.
Delete: A3MP2 and A3W2.