HP StorageWorks P9000

Other manuals for HP StorageWorks P9000

Software Installation Guide128 pages

Reference Guide399 pages

Configuration Guide165 pages

Manual333 pages

Integration Guide29 pages

Questions and Answers:

S
soconnorSep 14, 2025
What does path rejected mean on HP StorageWorks P9000?
- R
  reedmarcSep 14, 2025
  If you encounter a 'Path Rejected' error (MCU/RCU) on your HP Storage, start by deleting the failed path. Additionally, delete all paths and secondary systems that are not currently in use. Remember that the primary system can connect to a maximum of four secondary systems, with up to eight paths to each system. Ensure that all primary and secondary system ports are properly configured: use ordinary RCU target ports for secondary systems and initiator ports for primary systems. If necessary, connect to the secondary system to delete paths, reconfigure the ports, then reconnect to the primary system and add the path or secondary system again using Edit Path or Add RCU.
W
williamgibbsSep 14, 2025
How to fix invalid port mode error on HP StorageWorks P9000?
- J
  Jay VelezSep 14, 2025
  To fix an invalid port mode error on HP Storage, ensure the correct primary system port is configured as an initiator port and the correct secondary system port is configured as an RCU target port. Also, verify that you've entered the correct secondary system S/N, SSID, and path parameters, including port, link address, and logical address. If problems persist, delete the failed path. You may need to change the minimum paths setting or delete the secondary system to delete the path, then add the path or secondary system using Edit Path or Add RCU.
C
codywarnerSep 14, 2025
How to resolve logical blockade error on HP StorageWorks P9000 Storage?
- R
  Ray GarrettSep 14, 2025
  A logical blockade error on HP Storage can occur due to several reasons: * If the primary system port does not work, repair the port on the primary system. * If the secondary system port does not work, repair the port on the secondary system. Delete the path with Edit Path or Delete RCU, then add the path again with Edit Path or Add RCU. * If the path relay equipment does not work, repair the path relay equipment. Delete the path with Edit Path or Delete RCU, then add the path again with Edit Path or Add RCU. * If the connection cable is physically broken, replace the broken cable. Delete the path with Edit Path or Delete RCU, then add the path again with Edit Path or Add RCU.
S
smithbrittanySep 15, 2025
How to fix RCU port number mismatch on HP StorageWorks P9000 Storage?
- M
  Morgan HolmesSep 15, 2025
  To resolve an RCU Port Number Mismatch on HP Storage, first, ensure that you have entered the correct secondary system port number and correct it if necessary. Next, verify that the primary and secondary systems are physically connected. Finally, confirm that the Fibre Channel topology settings of the primary and secondary systems ports are correct.
W
warren51Sep 15, 2025
Why is HP Storage monitoring data not updating?
- L
  lcarrSep 15, 2025
  If HP Storage monitoring data is not updating even when the Monitoring Switch option is enabled, it might be because the time setting of SVP was changed. To resolve this, disable Monitoring Switch and then enable it again.
D
Danielle SummersSep 15, 2025
How to resolve HP Storage PSUE error by RCU?
- T
  Tonya BriggsSep 15, 2025
  To resolve a PSUE (pair suspended-error) by RCU on HP Storage, clear the error condition at the secondary system or S-VOL, then resynchronize the pair from the primary system. If you need to access the S-VOL to clear the error conditions, release the pair from the secondary system. After clearing the error conditions from S-VOL, restart the pair.
P
Phillip JonesSep 15, 2025
How to fix 'this path was not established' on HP StorageWorks P9000 Storage?
- I
  iwilsonSep 15, 2025
  To resolve the issue 'This path was not established' on HP Storage, delete the failed path. You may need to change the minimum paths setting or delete the secondary system (RCU) to delete the path. Then, add the path or secondary system using Edit Path or Add RCU.
N
Nicholas VargasSep 15, 2025
How to resolve HP Storage PSUE S-VOL failure?
- M
  madelinehuberSep 16, 2025
  To resolve a PSUE / S-VOL Failure error on HP Storage: * Check the path status on the RCU Status dialog box. If errors occurred on the path, clear the error conditions. * Clear any error conditions at the remote system or S-VOL, then resynchronize the pair from the primary system. * If you need to access the S-VOL to clear the error conditions, release the pair from the secondary system. After you clear the error conditions, re-create the pair.
X
xavier60Sep 16, 2025
How to resolve RCU port type mismatch on HP StorageWorks P9000 Storage?
- D
  Donald GarciaSep 16, 2025
  To resolve an RCU Port Type Mismatch on HP Storage, ensure that the secondary system port is configured as an RCU target port.
M
Mark GravesSep 16, 2025
How to resolve HP Storage PSUE MCU IMPL error?
- S
  stacieparkerSep 16, 2025
  To resolve a PSUE (pair suspended-error)/ MCU IMPL error on HP Storage, resynchronize the pair from the primary system. Note that an entire initial copy operation will be performed in response to the pairresync request.

HP StorageWorks P9000 Specifications

General

RAID Support	RAID 0, 1, 5, 6, 10
Interface	Fibre Channel, iSCSI, FCoE
Form Factor	Rack-mountable
Model	P9000
Operating System Compatibility	Windows, Linux, VMware, HP-UX
Host Interface	Fibre Channel, iSCSI, FCoE
Drive Interface	SAS, SSD
Drive Types Supported	SSD, SAS
Redundancy	Redundant controllers, power supplies, and fans
Management Software	HP StorageWorks Command View