EasyManuals Logo

HP Z230 User Manual

HP Z230
127 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #43 background imageLoading...
Page #43 background image
Computer Setup—Advanced
NOTE: Support for specific Computer Setup options may vary depending on the hardware
configuration.
Option Heading
Power-On Options Allows you to set:
POST messages—(Enable/Disable). This feature causes the system to display POST error
messages, which are error messages displayed on the monitor during the Power-On Self-
Test if the BIOS encounters some kind of problem while starting the computer. A POST error
message will display on screen only if the computer is capable of booting this far. If the
POST detects an error before this point, a beep code is generated instead. Default is
disabled.
Press the esc key for Startup Menu—(Enable/Disable). This feature controls the display of
the text “Press the esc key for Startup Menu” during POST. Neither this text nor any other
(for example, the Ownership Tag) is displayed on Windows 8 systems that have Fast Boot
support.
Option ROM Prompt—(Enable/Disable). This feature causes the system to display a
message before loading option ROMs. Default is enabled.
After Power Loss—(off/on/previous state). Default is Power off. Setting this option to:
Power off—Causes the computer to remain powered off when power is restored.
Power on—Causes the computer to turn on automatically as soon as power is restored.
Previous state—Causes the computer to turn on automatically as soon as power is
restored, if it was on when power was lost.
NOTE: If you turn off the computer using the switch on a power strip, you will not be able to use
the suspend/sleep feature or the Remote Management features.
POST Delay (in seconds). This feature adds a user-specified delay to the POST process.
This delay is sometimes needed for hard drives that spin up so slowly that they are not ready
to boot by the time POST is finished. The POST delay also gives you more time to select f10
to enter Computer Setup (f10) Utility. Default is None.
Remote Wakeup Boot Source (remote server/local hard drive). Default is Local hard drive.
Factory Recovery Boot Support—(Enable/Disable). This feature enables the BIOS to redirect
the boot to a recovery partition on the user hard drive, if one is present. Some versions of the
recovery software honor the f11 key press even when this feature is disabled. Default is
disabled.
Bypass f1 Prompt on Configuration Changes— (Enable/Disable). Allows you bypass the
confirmation step after changes are made. Default is enabled.
BIOS Power-On This feature enables you to specify a time for the computer to start automatically.
Onboard Devices Allows you to set resources for or disable Legacy devices.
Select the Legacy device's IRQ, DMA, and I/O Range. The settings may not take effect for all
operating systems. To hide a device from the operating system, see Security > Device Security.
Bus Options Allows you to enable or disable:
PCI SERR# Generation—(Enable/Disable) Default is enabled.
PCI VGA Palette Snooping—(Enable/Disable) Sets the VGA palette snooping bit in PCI
configuration space; only needed when more than one graphics controller is installed.
Default is disabled.
PCI Latency Timer—Sets PCI Clock speed. (32/64/96/128/160/192/224/248). 128 PCI
Clocks is the default.
Computer Setup (f10) Utility 33

Table of Contents

Other manuals for HP Z230

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the HP Z230 and is the answer not in the manual?

HP Z230 Specifications

General IconGeneral
Product typeWorkstation
Motherboard chipsetIntel® C226
ECCYes
Memory slots4x DIMM
Internal memory4 GB
Memory channelsDual-channel
Memory clock speed1600 MHz
Internal memory typeDDR3-SDRAM
Maximum internal memory32 GB
Memory layout (slots x size)1 x 4 GB
Chassis typeDesktop
Product colorBlack
Country of originChina
Placement supportedVertical
Number of 3.5\" bays1
Water cooling systemNo
HDD speed7200 RPM
RAID levels0, 1
HDD interfaceSATA
Storage mediaHDD
Optical drive typeDVD Super Multi
Total storage capacity500 GB
PS/2 ports quantity2
DisplayPorts quantity3
Serial ports quantity-
USB 2.0 ports quantity6
VGA (D-Sub) ports quantity0
USB 3.2 Gen 1 (3.1 Gen 1) Type-A ports quantity4
Ethernet LAN data rates10, 100, 1000 Mbit/s
On-board graphics card ID0x412
Discrete graphics card modelNot available
On-board graphics card modelIntel® HD Graphics 4600
Maximum on-board graphics card memory1.74 GB
On-board graphics card base frequency350 MHz
On-board graphics card DirectX version11.1
On-board graphics card dynamic frequency (max)1150 MHz
Power supply240 W
Tcase72.72 °C
Bus typeDMI2
SteppingC0
Processor cache6 MB
Processor modeli5-4570
System bus rate5 GT/s
Processor familyIntel® Core™ i5
Processor socketLGA 1150 (Socket H3)
Processor codenameHaswell
Processor frequency3.2 GHz
Processor cache typeSmart Cache
Processor lithography28 nm
Processor manufacturerIntel
Processor front side bus- MHz
PCI Express slots version3.0
Processor boost frequency3.6 GHz
Processor operating modes64-bit
PCI Express configurations1x16, 2x8, 1x8+2x4
Thermal Design Power (TDP)84 W
Maximum number of PCI Express lanes16
Memory clock speeds supported by processor1333, 1600 MHz
Memory bandwidth supported by processor (max)25.6 GB/s
Operating system installedWindows 7 Professional
Scalability1S
Processor codeSR14E
Processor ARK ID75043
Intel TSX-NI version0.00
Processor package size37.5 x 37.5 mm
Graphics & IMC lithography22 nm
Supported instruction setsAVX 2.0, SSE4.1, SSE4.2
Thermal solution specificationPCG 2013D
Intel Identity Protection Technology version1.00
Weight and Dimensions IconWeight and Dimensions
Depth384 mm
Width337 mm
Height100 mm
Weight7200 g

Related product manuals