Need help?Do you have a question about the HPE ProLiant DL20 Gen10 and is the answer not in the manual?
General| Memory | Up to 64 GB DDR4 ECC UDIMM |
|---|---|
| Network | 2 x 1GbE ports |
| Form Factor | 1U rack |
| Memory Slots | 4 DIMM slots |
| Processor | Intel Xeon E-2200 series, Intel Pentium |
| Storage | Up to 4 LFF drives or 8 SFF drives |
| Power Supply | 500W |
| Chipset | Intel C242 |
| Storage Controller | HPE Smart Array S100i or optional HPE Smart Array controllers |
| Expansion Slots | 1 x PCIe 3.0 x16 |
Identifies components on the server's front panel, including drives, ports, and LEDs.
Explains the status and meaning of front panel LEDs and the UID button.
Details the components found on the server's rear panel, including slots, ports, and power supplies.
Illustrates and labels the key components located on the server's system board.
Explains the meaning of LED indicators on various drive types.
Shows the numbering scheme for drive bays across different server models.
Illustrates the location and numbering of fan bays within the server chassis.
Describes server behavior when fan mode is altered or a fan fails.
Provides methods to power on the server using the power button or iLO.
Outlines procedures for safely powering down the server, including controlled and forced shutdowns.
Step-by-step instructions for removing the server's front bezel.
Procedures for safely extending the server out of its rack mounting.
Detailed steps for safely removing the server from its rack installation.
Instructions for installing the server into a rack, including rail attachment.
Steps to remove the server's top access panel for internal component access.
Instructions for reinstalling the server's top access panel after maintenance.
Procedure for removing the riser cage to access expansion slots.
Steps for installing the riser cage into the server chassis.
Options for performing initial server installation based on user expertise.
Information about Hewlett Packard Enterprise's professional installation service.
Guides the user through server unboxing, hardware options, and initial configuration.
Describes the options available on the Power-On Self-Test (POST) screen.
Specifies clearances and airflow needs for proper server installation and cooling.
Details the recommended ambient temperature range for server operation.
Outlines electrical regulations and precautions for server power installation.
Important safety warnings and precautions related to rack installation and server handling.
Critical warnings and cautions concerning server operation, hot surfaces, and energy packs.
Precautions and methods to prevent damage from electrostatic discharge (ESD) during handling.
Information and procedures for installing rack rail kits for server mounting.
Details about supported drive types, installation guidelines, and specific drive installations.
Lists available power supply units and their specifications.
Information and procedures for installing optical drive options in LFF and SFF chassis.
Guidelines and procedures for installing DIMMs, including population rules.
Describes the enablement option and its components for M.2 SSD and serial port.
Details the enablement board supporting two M.2 SATA SSDs and management.
Lists supported storage controllers for SATA and SAS drives.
Information on the energy pack as a backup power source for Smart Array controllers.
Lists supported PCIe expansion cards like storage controllers and network adapters.
Procedure for installing the FlexibleLOM adapter for network connectivity.
Information and warnings regarding transceiver options for network connections.
Explains the function of the chassis intrusion detection switch for security.
Details on installing and enabling the HPE TPM 2.0 Kit for enhanced security.
General guidelines for connecting and disconnecting server cables safely and correctly.
Diagrams and descriptions for connecting storage devices like drives.
Cabling diagrams for non-hot-plug drives with embedded and Smart Array controllers.
Cabling diagrams for hot-plug drives with different controller configurations.
Shows the SATA cabling for M.2 SSDs installed in different slots.
Cabling diagrams for non-hot-plug and Flex Slot power supplies.
Overview of iLO 5 as a remote server management processor for monitoring and control.
A server deployment tool for simplifying setup, installing OS, and integrating support software.
Embedded system ROM features for configuration, device setup, and system information.
The primary tool for configuring arrays on HPE Smart Array SR controllers.
Methods available for updating system firmware and ROM, including SPP and online flash.
Instructions and solutions for updating device drivers on the server.
Information on supported operating system versions for the server.
Explains NMI crash dump capabilities for diagnosing system hangs and reliability issues.
Lists available troubleshooting guides and resources for server issues.
Provides information about the server's internal real-time clock battery and handling precautions.
Step-by-step procedure for safely removing and installing the system battery.
Links to safety, compliance, and chemical substance information for HPE products.
Links to warranty information for various HPE server and networking products.
Details temperature, humidity, and altitude specifications for server operation.
Provides physical dimensions and weight specifications for the server.
Lists the specifications for the different power supply options available for the server.
To Next Page