Home
HPRT
Barcode Reader
N130BT
HPRT N130BT User Manual
4
of 1
of 1 rating
67 pages
Give review
Manual
Specs
To Next Page
To Next Page
To Previous Page
To Previous Page
Loading...
N130B
T User Manual
42
Multi code quan
tity
Operand: 0x4B
OFF
2
3
......
6
7
Data
0x00
0x02
0x03
......
0x06
0x07
Set whether to
st
art
scanning
multiple barc
ode
modes at the
same time and
set the number
of
scanning bar
codes simultaneously
.
Multi code sensitivity
Operand: 0x4C
Leve
l 1
2
3
......
9
10
Data
0x00
0x01
0x03
......
0x09
0x0A
Note:
the
higher
the
level,
the
str
on
ger
the
ability
to
decode
the
double
c
ode,
but
the
correspo
nding time to decode the single c
ode will be longer
.
Buzz
er enables
Operand: 0x4D
The con
vert r
ate in HID mode
Operand: 0x4E
Enable
Disable
Data
0x01 (Def
ault)
0x00
F
ast
Normal
Slow
Data
0x01
0x02 (Def
ault)
0x0a
48
50
Table of Contents
Default Chapter
4
Table of Contents
4
Chapter 1 Introduction
8
Appearance
9
Dimension
10
Interface
11
Power On, Power off and Restart
12
Maintenance
12
Barcode Read
12
Use the Setting Barcode
13
Restore Factory Defaults
13
Chapter 2 Communication Interface
14
USB Interface
14
HID Virtual Keyboard
14
USB International Keyboard Setting
14
USB Virtual Serial Port
20
Bluetooth Interface
20
Set Scanner Switch Time (Bluetooth Mode Only)
20
Bluetooth Pop-Up Iphone Keyboard Settings (Bluetooth Mode Only)
21
VID & PID Table
21
Chapter 3 Scanning Mode
22
Manual Mode
22
Sense Mode
22
Sensitivity
23
Continuous Mode
23
Command Programming
24
Chapter 4 Illumination and Aiming
25
Aiming
25
Illumination
25
Read Success Prompt Tone
25
Chapter 5 Symbologies
26
1D Barcode Setting
26
Ena-8
26
Enable/Disable EAN-8
26
Enable/Disable 2/5-Bit Add-On Code
26
Convert EAN-8 to EAN-13
26
Ena-13
27
Enable/Disable EAN-13
27
Enable/Disable 2/5-Bit Add-On Code
27
Upc-E
27
Enable/Disable UPC-E
27
Transmit Check Character
27
Enable/Disable 2/5-Bit Add-On Code
28
Convert UPC-E to UPC-A
28
System Character Transmit
28
Upc-E1
29
Enable/Disable 2/5 Add-On Code
29
Upc-A
29
Enable/Disable UPC-A
29
Transmit Check Character
30
Enable/Disable 2/5-Bit Add-On Code
30
Transfer System Character
30
Code 39
31
Enable/Disable Code 39
31
Check Character Verification and Transmit
31
Enable/Disable Code 39 Full ASCII
31
Convert Code 39 to Code32
32
Code 32 Prefix
32
Code 93
32
Enable/Disable Code 93
32
Code 11
32
Enable/Disable Code 11
32
Transmit Check Character
33
Code 128
33
Enable/Disable Code 128
33
Code 128 <FNC4
33
Codabar
34
Enable/Disable Codabar
34
Start and Stop Characters
34
Msi
34
Enable/Disable MSI
34
Check Bit Algorithm
35
Transmit Check Character
35
Interleaved 2 of 5
35
Enable/Disable Interleaved 2 of 5
35
Check and Transmit Character
35
Convert I 2 of 5 to EAN-13
36
Matrix 2 of 5
36
Enable/Disable Matrix 2 of 5
36
Check and Transmit Character
36
Industrial 2 of 5
37
Enable/Disable Industrial 2 of 5
37
Standard 25
37
Enable/Disable Standard 25
37
Issn
37
Isbn
38
Data Bit Setting
38
Isbt 128
38
Enable/Disable ISBT 128
38
Gs1 128
38
Enable/Disable GS1 128
38
Gs1-128 Emulation Mode for UCC/EAN Composite Code
38
GS1 Databar
39
Enable/Disable GS1 Databar
39
Convert GS1 Databar to UPC/ENA
39
GS1 Databar Limited
39
Enable/Disable GS1 Databar Limited
39
GS1 Databar Expanded
39
Enable/Disable GS1 Databar Expanded
39
1D Barcode Inverse
40
1D Barcode Anti-Color
40
2D Barcode Setting
41
Pdf417
41
Enable/Disable PDF417
41
Data Matrix
41
Anti-Color
41
Enable/Disable Data Matrix
41
Mirror Images
41
Inverse
42
Enable/Disable QR
42
Enable/Disable Micro QR Code
42
Anti-Color
43
Aztec
43
Inverse
43
Han Xin
44
Anti-Color
44
Inverse
44
Chapter 6 Troubleshooting
45
Chapter 7 Scanner Settings
46
Barcode Setting Format
46
Version Number--HYRS_RE
46
General Settings (Default HID Single Scan Mode)
47
Host Mode
47
Trigger Mode (Single Scanning, Scanning Continuously, Auto Sensing)
47
Default Parameters (Restore Factory Settings)
47
Decoding Timeout（0.1S~9S
47
Data Prefix
48
Data Suffix
48
Aiming Device (ON/OFF)
48
Illumination Light (ON/OFF)
48
Multi Code Quantity
49
Multi Code Sensitivity
49
Buzzer Enables
49
The Convert Rate in HID Mode
49
Timeout Setting of the same Barcode in Non-Single Scan Mode
50
Sensitivity
50
Center Aiming Decode Setting
50
Barcode Function Settings
52
ITF Cut the First few Bits of Data
52
Convert Grouping Character to Space
52
Remove Zero Data at the Beginning of Barcode
52
Remove or Reduce Space
52
Skip the Number of Characters before Barcode Data
53
Skip the Number of Characters after Barcode Data
53
Barcode Data Case Conversion
53
Insert Characters into Barcode Data
54
Compound Command Parameters
54
Common Suffix
54
Appendix Ⅰ Barcode Enabling Settings
55
Appendix Ⅱ Data Code Prefix and Suffix
57
Appendix Ⅲ ASCII Code Table
64
4
Based on 1 rating
Ask a question
Give review
Questions and Answers:
Need help?
Do you have a question about the HPRT N130BT and is the answer not in the manual?
Ask a question
HPRT N130BT Specifications
General
Brand
HPRT
Model
N130BT
Category
Barcode Reader
Language
English
Related product manuals
HPRT HT800
94 pages
To Next PageTo Next PageTo Previous PageTo Previous Page
Loading...
Need help?
General
