Why does my Hunter Douglas Silhouette Indoor Furnishing shading not raise or lower completely?
If your Hunter Douglas Indoor Furnishing shading isn't raising or lowering fully, check that the fabric isn't catching on any brackets or window components. You may also need to adjust the upper and/or lower bottom rail travel limits.
What to do if the Hunter Douglas Silhouette motor does not operate?
If the Hunter Douglas Indoor Furnishing motor isn't working, ensure the DC power supply is securely plugged into the wall outlet and the outlet has power. Verify the control device is programmed correctly by referring to its documentation. Check that all wire connections are secure and properly connected. As a test, with the power off, reverse the polarity of the motor wires and try operating the shading again. Also, confirm that wiring run guideline lengths haven't been exceeded.
What to do if Hunter Douglas Silhouette shading will not fit into the installation brackets?
If your Hunter Douglas Indoor Furnishing shading doesn't fit into the installation brackets, first check if a battery wand is interfering. Ensure the brackets are level and aligned, adjusting or shimming if necessary. Make sure mounting screw heads are flush against the brackets and the headrail is fully inserted, allowing the locking lever to slide over it.
What to do if Hunter Douglas Silhouette shading raises or lowers unevenly?
If your Hunter Douglas Indoor Furnishing shading raises or lowers unevenly, if the fabric rubs, or the bottom rail is uneven when fully raised, check that the window is square by measuring the diagonals. Also, ensure the installation brackets are level, using shims if needed. Consider adjusting the Bottom Rail Weight.
Why is my Hunter Douglas Silhouette Indoor Furnishing shading hard to raise or lower, or will not raise or lower?
If your Hunter Douglas Indoor Furnishing shading is difficult to move, consider these points: These shadings shouldn't be forced into tight inside mount window openings. For inside mounts, confirm the headrail is correctly installed and that there's adequate clearance between the shading's ends and the window casement. Also, check that the installation brackets are level and properly aligned.
What to do if Hunter Douglas Silhouette Indoor Furnishing shading does not operate when pushing up or pulling down the wand?
If your Hunter Douglas Indoor Furnishing shading isn't responding to wand movements, try these steps: Unplug the power cable from the motor, then lift the wand to discharge any residual power before plugging it back in. A green LED should flash, indicating power. If it flashes red, the batteries are likely drained and need replacement. Also, ensure the batteries in the battery wand, satellite battery pack, or C-size satellite battery wand are correctly inserted and fresh.
How to fix an uneven center gap in Hunter Douglas Two-On-One Headrail Window Blinds?
If the center gap of your Hunter Douglas Two-On-One Headrail window blinds is not even from top to bottom, ensure the entire length of the headrail is straight and level. If the center is higher, the gap will close; if lower, it will increase. Adjust the height of each bracket by moving it within the screw slots or using shims if necessary.
Why are my Hunter Douglas Window Blinds hard to raise or lower?
If your Hunter Douglas window blinds are hard to raise or lower, or will not raise or lower, and they are an inside mount, ensure there is enough clearance between the ends of the shading and the window casement. For EasyRise™ models, verify the universal cord tensioner is correctly mounted by pulling down on the spring to relieve tension and pulling the tensioner to the bottom of the cord loop, then properly mount it according to the included instructions. Also, check that the installation brackets are level and use shims to level them if necessary.
What to do if the universal cord tensioner grabs onto the cord upon operation of Hunter Douglas EasyRise Window Blinds?
If your Hunter Douglas EasyRise window blinds' universal cord tensioner grabs the cord during operation, ensure the universal cord tensioner is properly mounted. Reinstall if needed.
How to fix Hunter Douglas Window Blinds that raise or lower unevenly?
If your Hunter Douglas window blinds raise or lower unevenly, or the bottom rail is uneven when fully raised, check if the window is square by measuring the diagonals and ensure the installation brackets are level. Use shims to level if necessary.
General| Material | Fabric |
|---|---|
| Light Control | Adjustable |
| UV Protection | Yes |
| Operating Systems | PowerView Motorization |
| Available Widths | Up to 144 inches |
| Privacy | Adjustable |
| Vane Sizes | 2 inches |
| Customization | Yes |
To Next Page