What to do if my Hytera PDC7 fails to initiate a group call?
If your Hytera Radio fails to initiate a group call, it could be due to a few reasons: * The group call might be incorrectly configured. Check the configuration. * The group might not exist in the system. Add the group to the system. * The radio might not be a member of the group. Add the radio to the group on the system side.
Why does my Hytera PDC7 display in the status bar?
If the Hytera Radio displays in the status bar, it could be due to several reasons: * Incorrect configuration of RX Base Frequency, TX Base Frequency, Control Channel Spacing, Network, or Authentication. Ensure these settings are correctly configured. * Low RSSI of the current base station. To solve this, choose Settings -> PMR -> Power level and set the Power level to High. Additionally, choose Settings -> PMR -> Scan and turn Background hunt on. * The narrowband network is disabled. Enable it by tapping Narrowband in the control center of the radio or by going to Settings -> PMR -> Narrowband and turning it on.
Why does my Hytera Radio fail to initiate an all call and display 'Service disabled'?
If your Hytera Radio fails to initiate an all call and displays 'Service disabled' on the screen, it could be due to: * Incorrect all call configuration. Check the configuration. * All Call being disabled on the system. Enable all call on the system.
What to do if my Hytera PDC7 shows error code 0x06, 0x07, 0x08 0x09, 0x0A, or 0x0B when powering on?
If your Hytera Radio shows error code 0x06, 0x07, 0x08 0x09, 0x0A, or 0x0B when powering on, it indicates that the radio is experiencing an abnormality during startup. Try restarting the radio to resolve this issue.
What to do if Hytera PDC7 fails to initiate the emergency call by pressing Top Key?
If your Hytera Radio fails to initiate the emergency call by pressing the Top Key, it indicates that the emergency call service is incorrectly configured. Check the configuration.
What to do if my Hytera PDC7 shows error code 0x01 or 0x02 when powering on?
If your Hytera Radio shows error code 0x01 or 0x02 when powering on, it means that the previous upgrade was abnormal. Refer to Multi-mode Advanced Radio_Upgrade Guide_R1.5_V1.0 to upgrade the radio.
What to do if my Hytera Radio shows error code 0x05 when powering on?
If your Hytera Radio shows error code 0x05 when powering on, it indicates that the previous programming was abnormal. Reprogram the radio.
What to do if Hytera PDC7 Radio has no response when I choose Settings -> PMR, and tap Scan?
If choosing Settings -> PMR, and tapping Scan on your Hytera Radio results in no response, it means that the current channel doesn’t satisfy the conditions for scan. Configure the scan list and add available channels.
General| Channel Capacity | 1024 |
|---|---|
| Channel Spacing | 12.5/20/25KHz |
| Ingress Protection | IP67 |
| Frequency Range | UHF: 400-527 MHz; VHF: 136-174 MHz |
| Zone Capacity | 64 |
| Operating Voltage | 7.4 V |
| Battery | Li-ion |
| Display | 2.4 inch |
| Operating Temperature | -30℃ ~ +60℃ |
| Storage Temperature | -40℃ ~ +85℃ |
| RF Power Output | UHF: 4W; VHF: 5W |
| GPS | Yes |
Introduces how to manage PDC760 through Smart MDM (Mobile Device Management).
Details preparations for using Smart MDM, including software and licenses.
Instructions for connecting the radio to Smart MDM via Wireless or Wired mode.
Details on how to log in to the Smart MDM Admin Client for radio programming.
Explains the methods for creating a new radio configuration template.
Covers configuration of broadband features for the radio.
Details on configuring Access Point Name (APN) settings for network connectivity.
Configuration steps for the radio in conventional mode.
Prepares data elements like Dial Rule, Radio ID, Contact, Channel, and Zone.
Guides through basic configuration parameters for conventional mode.
Manages radio mobility features.
Configuration of scan feature to monitor multiple channels for incoming calls.
Configuration of roaming feature for communication across different base stations.
Configures voice service parameters.
Configuration to enable initiating private calls on the radio.
Configuration to enable initiating group calls on the radio.
Configuration to enable initiating all calls on the radio.
Configuration of digital emergency call features and emergency key.
Configuration of Priority Interrupt feature for call interruption.
Configures data service parameters.
Configuration for sending text messages on the radio.
Configuration for data forwarding between radios via serial port.
Configures security features.
Configuration of End-to-End Encryption (E2EE) for secure communication.
Configuration for encrypting data and communication over the air interface.
Configuration of Man Down alarm feature for user safety.
Configuration of Lone Worker alarm feature for user safety.
Configures analog services.
Configuration of analog channels, including frequencies and zones.
Configuration of analog emergency call system, type, and key.
Configuration for radio positioning and location reporting.
Prepares data for trunking mode, including Dial Rule, Radio ID, Network, Channel, Contact.
Basic configuration settings for trunking mode operation.
Configuration of Dial Rule and Radio ID for trunking mode.
Configuration of network settings like Network Model and ID for trunking.
Configuration of TSCC (Trunked Subscriber Color Code) for base station registration.
Configuration of contacts for private and group calls in trunking mode.
Configuration of subgroup lists for organizing contacts in trunking mode.
Configures voice service parameters in trunking mode.
Configuration to enable initiating private calls in trunking mode.
Configuration to enable initiating group calls in trunking mode.
Configuration to enable broadcast group calls in trunking mode.
Configuration to enable all calls in trunking mode.
Configures message service parameters in trunking mode.
Configuration for sending text messages in trunking mode.
Configuration for status messages in trunking mode.
Configuration for data forwarding between radios via serial port in trunking mode.
Configuration of emergency call parameters and emergency key in trunking mode.
Configures security features in trunking mode.
Configuration of authentication mechanisms for trunking radio and system.
Configuration of End-to-End Encryption (E2EE) for secure communication in trunking mode.
Configuration for radio positioning and location reporting in trunking mode.
Overview of app installation and uninstallation control via Smart MDM.
Steps for installing and uninstalling applications remotely using Smart MDM.
Preparations required for app installation/uninstallation via Smart MDM.
Procedure for uploading an application file to Smart MDM.
Steps to install an uploaded application on the radio via Smart MDM.
Procedure for uninstalling applications from the radio via Smart MDM.
Methods for users to install and uninstall applications directly on the radio.
Configuring permissions for app installation and uninstallation on the radio.
Steps for installing an application on the radio through the App Store.
Methods for uninstalling applications from the radio via App Store, App Center, or App Manager.
Overview of the operation flow for key management before using security features.
Lists preparations required for key management procedures.
Steps to generate a key application form using Smart MDM Admin Client.
Procedure for an administrator to add keys using KMC.
Methods for generating a key pack using KMC.
Steps to upload and push the generated key pack to the radio.
How to check the execution status of key upload and push operations.
Process to apply for licenses for paid features from Hytera.
Logging into the Smart MDM Admin Client to manage licenses.
Uploading the license file through the Smart MDM Admin Client.
Importing the uploaded license to the radio.
Verifying the status of paid feature licensing on the radio.
Guide to managing radios using Smart MDM Lite.
Preparations needed for radio management with Smart MDM Lite.
Installing Smart MDM Lite software.
Connecting the radio to the PC for management with Smart MDM Lite.
Methods for programming radios using Smart MDM Lite.
Managing applications on the radio using Smart MDM Lite.
Managing encryption keys using Smart MDM Lite.
Operation flow for key management with Smart MDM Lite.
Generating a key application form via Smart MDM Lite.
Importing an encryption key pack using Smart MDM Lite.
Enabling paid features by applying and importing licenses via Smart MDM Lite.
Troubleshooting common issues.
Troubleshooting common warning prompts displayed on the radio.
Troubleshooting trunking mode specific warning prompts.
Troubleshooting conventional mode specific warning prompts.
Troubleshooting prompts encountered within the Smart MDM application.
To Next Page
