Icom IC-9700 - Reflector Linking

Cmd. Sub cmd. Data Description
15
*
1
12 0000 ~ 0255 Read SWR meter level
( 0000=SWR1.0, 0048=SWR1.5,
0080=SWR2.0, 0120=SWR3.0)
13 0000 ~ 0255 Read ALC meter level
(0000=Minimum to 0120=Maximum)
14 0000 ~ 0255 Read COMP meter level
(0000=0 dB, 0130=15 dB, 0210=25.5 dB)
15 0000 ~ 0255 Read Vd meter level
(0000=0 V, 0013=10 V, 0241=16 V)
16 0000 ~ 0255 Read Id meter level
( 0000=0 A, 0121=10 A, 0241=20 A)
16* 02 00 to 03 Send/read the Preamp/External Preamp
(00=P.AMP (OFF)/EXT-P.AMP (OFF),
01=P.AMP (ON)/EXT-P.AMP (OFF),
02=P.AMP (OFF)/EXT-P.AMP (ON),
03=P.AMP (ON)/EXT-P.AMP (ON))
12 01 to 03 Send/read the AGC time constant
(01=FAST, 02=MID, 03=SLOW)
22 00 or 01 Send/read the Noise blanker
(00=OFF, 01=ON)
40 00 or 01 Send/read the Noise reduction
(00=OFF, 01=ON)
41 00 or 01 Send/read the Auto Notch function
(00=OFF, 01=ON)
42 00 or 01 Send/read the Repeater tone
(00=OFF, 01=ON)
43 00 or 01 Send/read the Tone squelch
(00=OFF, 01=ON)
44 00 or 01 Send/read the Speech compressor
(00=OFF, 01=ON)
45 00 or 01 Send/read the Monitor [MONI] function
(00=OFF, 01=ON)
46 00 or 01 Send/read the VOX function
(00=OFF, 01=ON)
47 00 to 02 Send/read the BK-IN function
( 00=BK-IN OFF, 01=Semi BK-IN ON,
02=Full BK-IN ON)
48 00 or 01 Send/read the Manual Notch function
(00=OFF, 01=ON)
4A 00 or 01 Send/read the AFC function
(00=OFF, 01=ON)
4B 00 or 01 Send/read the DTCS function
(00=OFF, 01=ON)
4F 00 or 01 Send/read the Twin peak lter
(00=OFF, 01=ON)
( Can be turned ON only when Mark and Shift
are set to 2125 Hz and 170 Hz, respectively)
50 00 or 01 Send/read the Dial lock function
(00=OFF, 01=ON)
56 00 or 01 Send/read the DSP IF lter type
(00=SHARP, 01=SOFT)
57 00 to 02 Send/read the Manual Notch width
(00=WIDE, 01=MID, 02=NAR)
58 00 to 02 Send/read SSB transmit bandwidth
(00=WIDE, 01=MID, 02=NAR)
( One of following values is applied, depending
on the “COMP” status (ON or OFF):
WIDE (Command: 1A 05 0017),
MID (Command: 1A 05 0018) or
NAR (Command: 1A 05 0019))
59 00 or 01 Send/read the sub band (the Dualwatch
function)
(00=OFF, 01=ON)
5A 00 or 01 Send/read the satellite mode
(00=OFF, 01=ON)
5B 00 to 02 Send/read the DSQL (Digital Call Sign
squelch)/CSQL (Digital Code squelch) setting
(DV mode only)
( 00=OFF, 01=DSQL,02=CSQL)
5C 00 to 02 Set the GPS TX mode
(00= OFF, 01= D-PRS, 02= NMEA)
00 to 03,
06 to 09
Set the Tone squelch function
( 00=OFF, 01=TONE, 02=TSQL, 03=DTCS,
06=DTCS (T), 07=TONE (T)/DTCS (R),
08=DTCS (T)/TSQL (R),
09=TONE (T)/TSQL (R))
65 00 or 01 Set the IP Plus function
(00=OFF, 01=ON)
D Command table (Continued)
Cmd. Sub cmd. Data Description
17*
3
See p. 10 Send CW messages
18 00 Turn OFF the transceiver
01*
4
Turn ON the transceiver
19*
1
00 Read the transceiver ID
1A* 00
See pp. 14, 15 Send/read memory contents
01 See p. 15 Send/read band stacking register contents
02*
5
See pp. 15, 16 Send/read memory keyer contents
03 See p. 16 Send/read the selected IF lter width
04 See p. 16 Send/read the selected AGC time constant
05 0001 See p. 16 SET > Tone Control/TBW > RX >
Send/read SSB RX HPF/LPF settings
0002 00 to 10 SET > Tone Control/TBW > RX >
Send/read SSB RX Tone (Bass) level
(00=–5 to 10=+5)
0003 00 to 10 SET > Tone Control/TBW > RX >
Send/read SSB RX Tone (Treble) level
(00=–5 to 10=+5)
0004 See p. 16 SET > Tone Control/TBW > RX >
Send/read AM RX HPF/LPF settings
0005 00 to 10 SET > Tone Control/TBW > RX >
Send/read AM RX Tone (Bass) level
(00=–5 to 10=+5)
0006 00 to 10 SET > Tone Control/TBW > RX >
Send/read AM RX Tone (Treble) level
(00=–5 to 10=+5)
0007 See p. 16 SET > Tone Control/TBW > RX >
Send/read FM RX HPF/LPF settings
0008 00 to 10 SET > Tone Control/TBW > RX >
Send/read FM RX Tone (Bass) level
(00=–5 to 10=+5)
0009 00 to 10 SET > Tone Control/TBW > RX >
Send/read FM RX Tone (Treble) level
(00=–5 to 10=+5)
0010 See p. 16 SET > Tone Control/TBW > RX >
Send/read DV RX HPF/LPF settings
0011 00 to 10 SET > Tone Control/TBW > RX >
Send/read DV RX Tone (Bass) level
(00=–5 to 10=+5)
0012 00 to 10 SET > Tone Control/TBW > RX >
Send/read Auto DV RX Tone (Treble) level
(00=–5 to 10=+5)
0013 See p. 16 SET > Tone Control/TBW > RX >
Send/read CW RX HPF/LPF settings
0014 See p. 16 SET > Tone Control/TBW > RX >
Send/read RTTY RX HPF/LPF settings
0015 00 to 10 SET > Tone Control/TBW > TX >
Send/read SSB TX Tone (Bass) level
(00=–5 to 10=+5)
0016 00 to 10 SET > Tone Control/TBW > TX >
Send/read SSB TX Tone (Treble) level
(00=–5 to 10=+5)
0017 See p. 16 SET > Tone Control/TBW > TX >
Send/read SSB TX bandwidth for wide
0018 See p. 16 SET > Tone Control/TBW > TX >
Send/read SSB TX bandwidth for mid
0019 See p. 16 SET > Tone Control/TBW > TX >
Send/read SSB TX bandwidth for narrow
0020 See p. 16 SET > Tone Control/TBW > TX >
SSB-D TX passband width
0021 00 to 10 SET > Tone Control/TBW > TX >
Send/read AM TX Tone (Bass) level
(00=–5 to 10=+5)
0022 00 to 10 SET > Tone Control/TBW > TX >
Send/read AM TX Tone (Treble) level
(00=–5 to 10=+5)
0023 00 to 10 SET > Tone Control/TBW > TX >
Send/read FM TX Tone (Bass) level
(00=–5 to 10=+5)
0024 00 to 10 SET > Tone Control/TBW > TX >
Send/read FM TX Tone (Treble) level
(00=–5 to 10=+5)
0025 00 to 10 SET > Tone Control/TBW > TX >
Send/read DV TX Tone (Bass) level
(00=–5 to 10=+5)
0026 00 to 10 SET > Tone Control/TBW > TX >
Send/read DV TX Tone (Treble) level
(00=–5 to 10=+5)
Remote control
5