Need help?Do you have a question about the Icom IC-M324G and is the answer not in the manual?
General| Brand | Icom |
|---|---|
| Model | IC-M324G |
| Category | Transceiver |
| Language | English |
Essential safety and usage information for the transceiver.
Explains specific terms and symbols used in the manual.
Highlights key capabilities and design aspects of the transceiver.
Guidelines for proper installation and RF exposure compliance.
Explains how the Maximum Permissible Exposure radius is calculated.
Rules for call priorities, including distress and safety calls.
Guidelines on information overheard and appropriate language.
Requirements for ship station and operator licenses.
Identification and function of front panel controls.
Explanation of icons and information shown on the transceiver's display.
Details on the microphone's buttons and operation.
Explanation of how to assign and use softkey functions.
Procedure for inputting the Maritime Mobile Service Identity code.
Procedure for inputting the Automatic Transmitter Identification System code.
How to choose between different operating channels.
How to select appropriate channel groups for different regions.
How to access and monitor weather channels.
How to set audio volume and background noise suppression.
Step-by-step guide for sending and receiving radio communications.
How to assign custom names to channels for easier identification.
Procedure to store frequently used channels for quick recall.
How to prevent accidental button presses on the microphone.
How to set the brightness of the display and keys.
How to clear water from the speaker grill using a vibration function.
Explanation of Priority and Normal scanning modes.
How to mark channels for inclusion in scan lists.
Steps to initiate and manage channel scanning.
Overview of how Dualwatch and Tri-watch functions operate.
How to activate and use Dualwatch and Tri-watch modes.
How to enter and manage individual and group DSC addresses.
Procedure for adding a 9-digit Group ID for DSC communication.
How to remove previously entered DSC addresses.
Manual input of ship's location and UTC time for DSC calls.
Steps to initiate an emergency distress transmission.
How to specify the nature of distress for a distress call.
Procedure to cancel a distress call before acknowledgment.
How to initiate a DSC call to a specific station.
How to initiate a DSC call to a pre-defined group of stations.
How to respond to an incoming individual DSC call.
How to broadcast a DSC message to all ships.
How to request a specific ship's location via DSC.
How to send your ship's location via DSC.
How to check if a specific vessel is within communication range via DSC.
How to respond to a polling request.
Procedures for handling distress alerts and acknowledgments.
How to manage distress relay messages.
How to process incoming individual DSC calls.
How to handle group, area, or all ships DSC broadcasts.
How to process incoming position requests.
How to process incoming position reports.
How to handle polling requests and test calls.
How to process test call acknowledgments.
Accessing and managing records of outgoing DSC calls.
Accessing and managing records of incoming DSC calls.
Setting up automatic responses to incoming DSC calls.
Configuration for automatic channel switching after distress calls.
Setting DSC alarm types and their activation.
Adjusting the squelch sensitivity for Channel 70.
Performing a diagnostic test on the DSC circuit.
How to make DSC calls via an connected AIS transponder.
General guidance on accessing and navigating menu options.
Step-by-step process to open the main menu.
An overview of all available options within the menu system.
Display of preset MMSI, ATIS codes, and GPS data.
Selecting between Normal and Priority scan modes.
Setting how long a scan pauses upon receiving a signal.
Configuring simultaneous monitoring of multiple channels.
Selecting channel sets based on region or type.
Setting up alerts for NOAA weather broadcasts.
Adjusting the brightness of the display and keys.
Adjusting the contrast level of the LCD screen.
Enabling or disabling audible feedback for button presses.
Details on wiring and port connections for various devices.
Instructions for connecting the MA-500TR AIS transponder.
Importance of the antenna and advice on selection and mounting.
Procedure for replacing a blown fuse in the power cable.
Guidelines for cleaning the transceiver safely.
List of items included with the transceiver.
Overview of general technical specifications like frequency and power.
Technical details related to the transmitter's performance.
Technical details related to the receiver's performance.
Specifications for the squelch function's sensitivity.
Physical measurements of the transceiver unit.
List and description of optional accessories for the transceiver.
A list of country codes used for identification.
To Next Page
