IDEC DD3S Series - Dimensions & Panel Cut-out

11
DD3S Series Display Units
IGHT
6.5 2020 20 20 6.5
20N + 13
33 30
10
423.5
End Plate
Binary
Display Unit
Dec/Hex
Display Unit
Character Display Unit
Spacer Unit
DD9Z-FY1-8
Panel Thickness 0.8 to 4
Display units can be combined
for up to 8 digits.
6.5
0
+0.5
+0.5
0
20N + 10.5 3.5 min.
30.516 min.
(when mounting
more than 8 units)
(21 min.
∗
)
N = No. of digits (N ≤ 8)
∗
When using a static mother board
Panel Cut-out
For Connector Wiring
For Use of Dynamic Mother Board
Dimensions & Panel Cut-out All dimensions in mm.
2-
color
Standard
No.
F3
**
F01
**
F3
**
GND
NC
A
D
LAT
BL
R/G
C
Vcc
B
DP
NC
GND
NC
+
-
LAT
BL
LT
1
Vcc
NC
DP
NC
GND
NC
A
D
LAT
BL
LT
C
Vcc
B
DP
NC
12
11
10
9
8
7
6
5
4
3
2
1
Terminal Arrangement
by Models
UP
DMC-2
11.3
(
45.5
)
1.6
1.5
4.5
13.5
(
26.9
)
Connector for Data Input
Screw
Spacer
Nut
DD3S
Housing
Connector
Spacer
DD3S Housing
PC Board
Nut
(M2.6)
Screw M2.6 × 18
1
2
3
4
5
6
7
8
9
10
11
12
(
10
)(
10
)(
10
)(
10
)
0
3
2
1
13
20 20 20
10 6
14
39 45
12-ø3.2 (for mounting mother board)
3-ø2.8 (for securing DD3S)
78 (Note)
Note: 38 mm for 2-digit mother board DD9Z-MB1-2
Dynamic Mother Board (not applicable to zero-suppress)
4-digit: DD9Z-MB1-4
2-digit: DD9Z-MB1-2
Note: The DD3S housing can be secured to the mother board using screws.
Recommended tightening torque is 3.5 N·m at the maximum. When
no spacer is used, the tightening torque must not exceed 2 N·m.
Substrate: Glass epoxy, 1.6-mm
thick
Screws (M2.6 × 18), M2.6-3 nuts, and spacers are supplied with
the mother board.
(Top View)
11
*
B
D <–>
Latch (10
1
)
Latch (10
3
)
7
*
(10
1
)
7
*
(10
3
)
DP (10
0
)
DP (10
2
)
Vcc
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
GND
<+> A
<1> C
Latch (10
0
)
Latch (10
2
)
7
*
(10
0
)
7
*
(10
2
)
6
*
DP (10
1
)
DP (10
3
)
For 4-digit
Input Terminal Arrangement
(Top View)
11
*
B
D <–>
Latch (10
1
)
NC
7
*
(10
1
)
NC
DP (10
0
)
NC
Vcc
1 2
3 4
5 6
7 8
9 10
11 12
13 14
15 16
17 18
19 20
GND
<+> A
<1> C
Latch (10
0
)
NC
7
*
(10
0
)
NC
6
*
DP (10
1
)
NC
For 2-digit
Numbers marked with
*
are the DD3S terminal numbers.
IGHT
33 45
6
11.3
42
45.
55
Applicable Wire: ø0.8mm maximum
AWG #22 maximum
0.6
12-ø1 Holes
411.3
2
2.5 × 11
20
Applicable PC board thickness: 1.6
DD9Z-CN1
UP
2
1
4
35
6
7
8
9
10
11
12
35
1.55 1.7 6.813.1
33
6
5
13.5
1.6
13
27.8
(min25)
Accessories (Optional)
Connector
Solder Terminal Connector PC Board Terminal Connector Retentive/One-way Insertion Connector
(DMC-1) (DMC-2) (DD9Z-CN1) (Note)
Note: Use DD9Z-CN1 in combination with DD9Z-ST1 connector
stopper.