IDTECK iTDC-SR - Dimension

To Next Page

To Previous Page

FEATURES

iTDC

p.13

3 DIMENSION

Unit: inch (mm)

Main Page

Table of Contents2
Safety Information8
Important Safety Instructions9
Notice to Prevent Trouble and Malfunction11
Notice for Nema Case11
Notice for Installation of Door Lock11
Notice for Installation of Door Lock or Automatic Door (24V)12
Notice for Connection of Power or Reader12
Notice for Connection of Communication12
Features14
Features for Itdc/ Itdc-SR14
Identifying Suppllied Parts18
Standard Parts in Package18
Optional Accessories18
Supplied Parts for Itdc/Itdc-Sr Package-1 or Package-2 (2 Doors)19
Supplied Parts for Itdc/Itdc-Sr Package-3 or Package-4 (3~4 Doors)19
Dimension20
Specification21
Product Overview23
Itdc / Itdc-Sr Mainboard23
Itdc/Itdc-SR Board Arrangement Table24
Optional Accessories26
Expansion I/O Board26
EIO88 Board Arrangement Table27
TCP/IP Module (IIM100)27
Keypad27
Lcd Display Module28
Preparation of Installation29
Configuration Depending on Type of Communication29
Configuration for Rs232 Communication29
Configuration for Rs422 Communication30
Configuration for Tcp/Ip Communication30
Tcp/Ip Configuration of Direct Communication30
Configuration of Installation for Tcp/Ip Bypass Communication31
Recommended Cable Type and Permissible Length of Cable32
How to Equip Optional Specification33
Equipment of Tcp/Ip Module (Iim100)33
Equipment of Expansion In/Output Board (Eio88)34
Equipment of Keypad35
Equipment of Lcd Module36
Product Installation37
Description of Ports for Wiring37
Itdc/Itdc-Sr Main Board Port37
Expansion I/O Board (Eio88) Port38
Procedure of Product Installation39
Board ID (Communication ID) Setting39
Earth Gnd Connection40
Connection of Earth Gnd When Installing Itdc/Itdc-Sr to Nema Case40
Case42
Power Wiring43
Input Device Wiring44
2-Door Control44
3-Door Control45
Output Device Wiring46
2-Door Control47
Wiring for Door Lock and Alarm in Power Fail Safe Mode47
Wiring for Door Lock, Alarm in Power Fail Secure Mode48
3-Door Control50
Wiring for Using 24V Door Lock or Automatic Door51
Reader Wiring51
2-Door Control51
3-Door Control (if External Reader and Internal Reader Are Connected to Door 1.)53
3-Door Control (if External Reader and Exit Button Are Connected to Door1)54
4-Door Control54
Wiring to Control Led/Buzzer of Reader55
How to Wire for Presenting Door Open Status by LED or Buzzer in Power Fail Secure Power Fail Secure55
How to Wire for Presenting Door Open Status by LED or Buzzer in Power Fail Secure Power Fail Safe55
Communication Wiring59
Rs232 Communication Port Connection59
Rs422 Communication Port60
Rs422 Connection (Independent Wiring)60
Connection (Multiple Itdc Connections)61
Connection Using the Tcp/Ip Module (Internal Version)63
External TCP/IP CONVERTER (ILAN422)65
Wiring for RS232 Communication65
Wiring for RS422 Communication65
Led Operation Status Check after Installation67
LED INDICATORS of the Itdc/ Itdc-SR67
Led Indicators of the Eio88 Expansion I/Oboard68
LED Indicators of In/Output Signal68
Basic Setting69
Initialization69
How to Use Keypad70
How to Enter the Setup Menu70
Door Setting71
Date and Time Setting72
Maximum User Setting72
Reference for LCD Display73
ID Registration74
Reference for LCD Display74
Setting Changes77
Setting Menu F178
Reader Mode Setting80
Anti Pass-Back Mode Setting81
Keypad Input Setting82
Duress Mode Setting83
Reader Mode Time Schedule Setting84
Reader Open Check Setting85
Reader Open Status85
Setting Menu F286
Time Setting88
Holiday Index Setting88
Comm ID(Communication ID, Board ID) Display89
Baud Rate Setting89
Master ID Change90
Event Memory Setting90
Door Open Alarm Setting91
Door Setting91
Holiday Setting92
Time Schedule Setting93
Defining Input Time in Compliance with Inputs95
Defining Output Time in Compliance with Reader97
System Initialize98
Event Clear99
Card ID Clear99
Time Schedule Clear100
Setting Menu F3101
ID Registration102
ID Deletion103
ID List105
Registered ID Count106
Max User Setting107
Stored Event Count108
Key Input Mode108
Arm/Disarm Code109
Arm/Disarm Port111
Arm Code Process Details112
Disarm Code Process Details113
Arm / Disarm Input Process Details114
Men Operation Mode Setting114
Input Time Schedule Mode Setting115
Setup Menu F4116
Version Check118
Ram Test118
Outputs Test119
Lcd Test119
Keypad Test120
Reader Test121
Input and Dip Switch Test121
Communication Test122
Appendix124
The Default Valures Depending on Input(Input Port / Reader Input)124
The Relation between Input and Output (2Door Set-Up: Itdc Board Default)124
The Relation between Input and Output (3Door Set-Up: Itdc Board Default)125
The Relation between Input and Output (3Door Set-Up: EIO88 Extension I/O Board Default)126
The Relation between Input and Output (4Door Set-Up: Itdc Board Default)127
The Relation between Input and Output (4Door Set-Up: EIO88 Default)128
Default Values on the Outputs Regarding Access Attempts (2Door Set-Up: Itdc Board Default)130
Default Values on the Outputs Regarding Access Attempts (3Door Set-Up: Itdc Board Default)131
Default Values on the Outputs Regarding Access Attempts (3Door Set-Up: EIO88 Default)132
Default Values on the Outputs Regarding Access Attempts (4Door Set-Up: Itdc Board Default)133
Default Values on the Outputs Regarding Access Attempts (4Door Set-Up: EIO88 Default)134
Troubleshooting136
The Device Dose Not Communicate with PC136
Please Check Wiring136
In the Case of RS232 Communication136
In the Case of RS422 Communication137
Please Check if the Communication Address Is Good137
Check Communication Address Setting of Software and the Device137
Please Check if the Communication Port Setting Is Good138
Please Check if the Termination Resistor Is Connected138
Please Check if the Device Is Grounded Well139
When Turning on the Device, Date / Time Is Not Displayed on the LCD and Special Characters Are Displayed139
This May Happen When the Device Is Not Initialized. Please Initialize the Device140
When Configuring the Device Using MASTER ID, Suddenly the Device Goes Back to the Normal Mode140
If You Do Not Input Anything for 60 Seconds in Setting Mode, the Device Goes Back to the Normal Mode140
The Device Does Not Go to Setting Mode after Inputting MASTER ID140
A MASTER ID May Have Changed141
The Device Work Well with RF Card, but Does Not Work When Inputting Card Number141
Please Check if Keypad Is Set to "ENABLE141
When the Device Have Read a Card, the Device Does Not Response or a Different Card Number Appears142
Please Check if a Reader Is Good142
Please Check if Wiring between a Reader and the System142
Please Check if Software Settings Are Good142
Remove Noise142
Registered Card Is Not Authenticated143
Please Check Output Setting of the Device143
Fcc Registration Information144
RMA Request145

IDTECK iTDC-SR - Dimension

Table of Contents

Other manuals for IDTECK iTDC-SR

Related product manuals