® 07-287 NS-PDP50 EnglishOnly.fm Page 25 Wednesday, July II, 2007 12:05 PM
i;]_ i_/,-_ih _IQ ©_'_©;_"_ ..... /_/_;_,_,-__ -_ _ "_"_ D
Troubleshooting
Problem Solution
ierAoi; ;ni oiionsio( • ii; su iiiiiii; isio(
work. an object betweenthe
remote control and the
remote control sensor on
the front of your plasma
TV.
• Makesure that the
batteries are installed
correctly. The + and -
symbols on the batteries
must align with the + and
- symbols in the battery
compartment.
• Makesure that you have
selectedthe correct mode,
for example, TV,VCR,and
so forth.
• Replacethe batteries.
Powei suiieniytuins oii ...... • Makesuietiaithe sieep
timer has not beenset.
• Makesurethat the channel
has not beset to Auto off.
• Makesure that the power
outlet is receiving power.
....Tieieis no piciuie oisoini ...... • Make suiethaiyoui
plasma TV isturned on.
• Makesure that your
plasmaTV is plugged into
a power outlet.
• Makesure that the power
outlet is receiving power.
• Tryanother channel. The
current channel may be
experiencing difficulties.
• If you are using an
antenna,adjust the
orientation of the antenna
or move it.
....Thepiciuieappeaisslowly ..... , Thisis noimai Duiing the
afterturning on your plasma startup process,the image
TV. is muted. If the picture
does not appearafter five
minutes, contact qualified
repair personnel.
................Thereis no color...........or poor * Aajusithe coioi
color. OSD.
• Makesure that your
plasma TVand aVCR are
not too close to each
other.
• Tryanother channel. The
current channel may be
experiencing difficulties.
• Makesure that all video
cablesare connected
correctly and securely.
• Pressany button to
restore the brightness
level.
Thepiciuiehashoiizoniaioi ..... • Make suie thai an
i vertical bars, or the picture electricalappliance or
"shakes." power tool is not
interfering with your
pIasmaTV.
_iiiiiiiiiii_
INSIGNIA
i
orientation.
ii • Make sure that an
electrical appliance or
power tool is not
interfering with your
plasmaTV.
• Thesignal from some
channels may be too weak.
Thepicture has lines or • If you are using an
streaks, antenna,adjust the
orientation.
Thepiciuieisgooii but...... • incieaseihevoiumel ....
thereisno sound, • PressMUTE to makesure
that the sound is not
muted.
• Tryanother channel.The
current channel may be
experiencing difficulties.
• Makesure that the audio
cables areconnected
........................................... ....... correctlY and secu!ely...............
Oneof the speakersdoes not • Adjust the audio balance.
produce sound. .......... ..............................
Unusual sounds are coming • A change in humidity or
from inside your plasma TV. temperature may result in ....
unusual sounds when you
turn your plasmaTV on or
off, This is normal and
does not indicate that your
plasmaTV is not working
correctly.
modelthe signai isout * AI usithe iesoiution oi
of range, the horizontal or vertical
frequency.
• Makesure that the PCis
connected correctly and
........................................ secure,Y:...................... .........
H _H
In PC mode,the picture has • Usethe autoadjust feature
vertical bars or stripes,there to automatically adjust the
is horizontal noise, or the image, or adjust the clock,
image position is incorrect, phase, or vertical or
horizontal position options
In PC mode,the color is • Make sure that the cables
.....unstable or there is only one are connected correctly
color, and securely.
• Reinstallthe PCvideo card .....
or driver.
25
To Next Page
Loading...
