Interlogix NXG-8-CB - Termination Links

170 pages

To Next Page

To Previous Page

xGen Lite Installation and Programming Guide 19

Termination Links

Put a jumper across TERM on the panel and the furthest device to ensure correct

RS-485 termination and avoid communication issues with signal reflection, etc.

Main Page

Table of Contents5
Important Information9
Limitation of Liability9
Product Warnings9
Warranty Disclaimers10
Disclaimer11
Intended Use11
Advisory Messages12
Introduction13
System Capacity13
Xgenlite Specifications14
Product Codes14
Mains Power Specifications15
Installation Instructions for Service Persons15
Power Supply Specifications15
General Features16
Current Consumption17
Output Current Rating18
Auxiliary Current and Battery Capacity18
Environmental18
Physical Dimensions and Weight19
Fuses19
Maintenance19
System Monitoring20
SIA and CID Reporting Code Descriptions20
EN 50131-3 and en 50136-2 Compliancy24
Options Affected by en 50131 Regulations24
Optional Functions25
EN 50131 Compliance Precautions25
NXG-8 Wiring Diagram26
NXG-8 Terminals27
NXG-8 Leds28
NXG-9 Wiring Diagram29
NXG-9 Terminals29
NXG-9 Leds29
Detector EOL Wiring29
Power Requirements30
Cable Requirements30
Grounding30
Shielding30
Termination Links31
Installing Panel32
Installing Legacy NX Modules32
Installing Antennas33
NXG-001 Plastic Enclosure34
NXG-003 Xgen Metal Enclosure35
Enrolling Modules35
Deleting Modules36
Arming and Disarming Your System38
Keypress Tamper38
Lock out on 3 Invalid Attempts38
Arm Your System in Away Mode38
Arm Your System in Stay Mode39
Arm Your System in Instant Stay Mode39
Arm Your System in Night Mode39
Disarm One or more Partitions39
Activate SOS Feature40
Programming Methods41
Account Access41
Method 1: DLX900 Management Software41
Method 2: Web Server43
Method 3: Ultrasync+ App47
Method 4: NXG-1820 Keypad53
Programming with Web Pages54
Recommended Items to Change54
Learning Wireless Zones55
Adding a User60
Adding a Keyfob61
Advanced Keyfob Programming61
Programming Cameras63
Configuring Email Reports67
Configuring OH Reports68
Enabling Push Notifications on Smartphone70
Z-Wave Home Automation Hub75
Adding Z-Wave Devices75
Programming Z-Wave Siren76
Removing Z-Wave Devices77
Adding Xgenlite to Existing Z-Wave Network as Secondary Controller78
Removing Xgenlite from Existing Z-Wave Network as Secondary Controller79
Adding Xgenlite to Existing Z-Wave Network as Primary Controller80
Relinquish Primary Control of Xgenlite to Another Controller81
Creating a Device Association83
Replacing a Failed Node84
Creating a Device Association84
Removing a Failed Node84
Rediscover Z-Wave Nodes85
Backup Z-Wave Network86
Reset Z-Wave Network86
Restore Z-Wave Network86
Send User Pins to Z-Wave Door Lock87
Programming Scenes89
Xgenlite with Amazon Alexa93
DLX900 Software95
Installing DLX90095
Upgrading from DL90095
Login to DLX95
Navigating the Main Window97
Customer Window98
Navigating the Menus99
Control Panel Menu100
Loading Control Panel Defaults100
Devices Menu101
Device Info102
Download Menu103
Reading Data104
Sending Data104
Tools Menu105
Programming with DLX900106
Programming Instructions for System Options106
Programming Instructions for Permissions110
Programming Instructions for Menus112
Programming Instructions for Holidays114
Programming Instructions for Users117
Programming Instructions for Zones120
Programming Instructions for Custom Zones123
Programming Instructions for Areas126
Programming Instructions for Schedules129
Programming Instructions for Arm-Disarm133
Programming Instructions for Communicator138
Programming Instructions for Ultrasync141
Programming Instructions for Event Lists143
Programming Instructions for Channels145
Programming Instructions for Zone Reporting149
Programming Instructions for System Event Reporting151
Programming Instructions for Actions153
Programming Instructions for Action Groups155
Programming Instructions for Scenes157
Programming Instructions for Outputs158

Interlogix NXG-8-CB - Termination Links

Table of Contents

Related product manuals