How to improve reduced flow in Jandy Pro VSPHP270AUT?
If your Jandy Water Pump has reduced flow, verify that the skimmer baskets, pump basket, and other screens are clean. Clean them if necessary. Also, check the filter and clean it if needed. Finally, check the valve positions and adjust them as necessary.
What to do if Jandy Pro VSPHP270AUT has no power?
To address the issue of no power to your Jandy Water Pump, ensure that the pump is properly connected to high voltage. Refer to section “3.2 Electrical Installation” for guidance.
What to do if my Jandy Pro VSPHP270AUT gets hot and shuts off?
If your Jandy Water Pump gets hot and shuts off periodically, ensure there's enough space around the motor for air circulation to keep it cool. Also, have a qualified electrician check for loose connections and the voltage at the pump motor during operation. The voltage must be within 10% of the motor's data plate rating. If it's not, contact a qualified electrician or your local power service provider.
How to fix air leaks in Jandy Water Pump?
If you still have air leaks in your Jandy Water Pump, check the suction side piping union. While the pump is running, try tightening the union. If the air leak persists, turn off the pump, loosen both unions, and slide the pump aside. Remove, clean, and reinstall both union o-rings. Reposition the pump and secure the union nuts by hand-tightening them. If the unions still don't seal, gently tighten them with tongue-and-groove pliers, being careful not to overtighten.
What to do if Jandy Pro VSPHP270AUT Water Pump is leaking water?
If the Jandy Water Pump is leaking water between the motor and the pump body, this is caused by a damaged or failed mechanical seal. Replace the seal.
How to fix low-voltage wiring in Jandy Pro VSPHP270AUT?
To resolve improper low-voltage wiring in your Jandy Water Pump, check the low-voltage wiring between the pump and the controller and correct it if necessary. Refer to section “3.2 Electrical Installation”.
How to configure address setting on Jandy Pro VSPHP270AUT Water Pump?
To correct an improper pump address setting on your Jandy Water Pump, ensure that pump dip switches 3 and 4 are set properly for your installation. Both should be OFF for use with a Variable-Speed Controller, or set to the proper address when connected to an AquaLink® RS controller, an AquaLink PDA, or an AquaLink Z4. Refer to section “3.2.4.1 Install with AquaLink® controller”.
Why are there bubbles in my Jandy Pro VSPHP270AUT basket?
If bubbles are present in the Jandy Water Pump basket, it indicates air is in the system. First, check the pool or spa water level to ensure it's at the proper level, preventing air from being drawn into the suction piping. If the water level is normal, turn off the pump and unlock the lid by turning the locking ring counter-clockwise until 'START' aligns with the ports. Remove the lid and inspect for debris around the lid seal seat or improper installation of the lid seal, as these can cause air leaks. Clean the lid seal and replace it on the lid. Then, put the lid back on the pump housing, align 'START' with the ports, and turn the locking ring clockwise until 'LOCKED' aligns with the ports. Hand-tighten the lid to ensure an airtight seal, avoiding the use of tools. Finally, turn the pum...
Covers basic safety precautions for electrical equipment and installation procedures.
Details risks of suction entrapment and essential prevention guidelines.
Addresses risks of electric shock, fire, and property damage from improper electrical connections.
Details requirements for electrical connections and safety for pump installation.
Ensures proper bonding and grounding for electrical safety during installation.
Instructions for secure and adequate electrical wiring and connections to the pump.
Steps for safely starting the pump after installation, including priming.
Lists symptoms like reduced flow, bubbles, leaks, and provides troubleshooting solutions.
Troubleshooting for controller LCD and pump LED issues, and connection errors.
General| Model | Pro VSPHP270AUT |
|---|---|
| Category | Water Pump |
| Type | Variable Speed |
| Horsepower | 2.7 HP |
| Phase | Single Phase |
| Motor Type | Permanent Magnet |
| Warranty | 3 years |
| Energy Efficiency | Energy Star Certified |
| Voltage | 230V |
| Control | Digital |
To Next Page