EasyManua.ls Logo

Jandy VSFHP185DV2A - User Manual

Jandy VSFHP185DV2A
72 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
H0661900_REVC
WARNING
FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and
qualified in pool equipment by the jurisdiction in which the product will be installed where such state or
local requirements exist. The maintainer must be a professional with sufficient experience in pool equipment
installation and maintenance so that all of the instructions in this manual can be followed exactly. Before
installing this product, read and follow all warning notices and instructions that accompany this product.
Failure to follow warning notices and instructions may result in property damage, personal injury, or death.
Improper installation and/or operation will void the warranty.
Improper installation and/or operation can create unwanted electrical hazard which can
cause serious injury, property damage, or death.
ATTENTION INSTALLER - This manual contains important information about the installation,
operation and safe use of this product. This information should be given to the owner/
operator of this equipment.
ENGLISH | FRANÇAIS | ESPAÑOL
INSTALLATION AND
OPERATION MANUAL
VSFHP185DV2A
VSFHP270DV2A
VSPHP270DV2A
Jandy
Variable-Speed Pumps

Table of Contents

Questions and Answers

  • B
    brucestevensonAug 1, 2025
    What to do if my Jandy VSFHP185DV2A motor won't start?
    • C
      christopher18Aug 1, 2025
      First, have a certified professional check the voltage on the main power terminal with the breaker on, ensuring it's within 10% of the motor's rating. Then, power cycle the motor by turning off the main breaker, waiting at least 5 minutes before restoring power. Also, inspect the RS-485 connection, checking for secure connections, corrosion, and any broken wires. Ensure the DIP switches 3 and 4 are in the OFF position. Finally, verify that the motor is scheduled to turn on at the current time according to the controller's settings.
  • Z
    Zoe BlackAug 6, 2025
    How to test Jandy Water Pump drive with RS-485 jumper method?
    • Q
      qblairAug 6, 2025
      Using small sections of 22 AWG wire, jump pins 1 to 3 and 2 to 4. Re-install the connector and attach the access cover. Apply power to the motor. The motor should spin at 2600 RPM indefinitely. If the motor works, there is a problem with the RS-485 line or with the controller.
  • W
    Wesley EscobarAug 10, 2025
    How to configure DIP switches on Jandy Water Pump?
    • J
      James WilsonAug 10, 2025
      The variable speed drive has two DIP switches; 3 and 4. These must both be in the OFF position for Pump 01. This is the configuration for all controllers that are not automation and the first pump for automation. If more than one variable speed pump is being controlled with an automation system, they must be in the proper configuration. Refer to the DIP switch section of the manual to configure the other motors.
  • B
    Bradley BarryAug 14, 2025
    Why does my Jandy VSFHP185DV2A motor start but then shut off?
    • L
      Lindsay WillisAug 14, 2025
      Debris might be stuck between the impeller and the diffuser. To resolve this, have a certified professional check if the drive shaft is seized with all power off. You can perform a quick test by inserting a 5/16" allen wrench through the back of the fan housing and into the drive shaft, then manually spin it to check for seizing. If you find large amounts of debris, inspect your strainer basket for any breaks and replace it if needed.
  • T
    Thomas ChambersAug 18, 2025
    How to fix improper low voltage wiring on Jandy VSFHP185DV2A Water Pump?
    • C
      catherinepowersAug 18, 2025
      Ensure the RS-485 connection is secure and free of broken wires. Inspect the low voltage wiring for corrosion; if found, cut off the wires and strip new leads, ensuring no broken wire pieces are inside the RS-485 connector. Also, verify the wiring of the RS-485 connector, ensuring the wire colors for pins 1-4 are Red, Black, Yellow, and Green.
  • B
    Benjamin BrownAug 22, 2025
    What to do if Jandy VSFHP185DV2A Water Pump motor experienced an error?
    • R
      Robert SmithAug 22, 2025
      Power cycle the motor. A fault code may appear on the controller. To clear the error, turn off the main breaker connected to the motor and wait at least 5 minutes before restoring power. Ensure the voltage in the capacitors is completely drained for a proper power cycle.
  • W
    Wendy WallaceAug 27, 2025
    How to check broken low voltage wiring on Jandy VSFHP185DV2A?
    • L
      Lorraine GravesAug 27, 2025
      With all power off, use a multimeter set to Ohms/Continuity to check the continuity of each low voltage line from the motor side to the controller side. If necessary, replace the RS-485 wires completely.

Summary

Important Safety Instructions

Safety Instructions

Essential safety precautions for electrical work, equipment usage, and compliance with codes.

Pool Pump Suction Entrapment Prevention Guidelines

Guidelines for preventing suction entrapment hazards in pools, spas, and hot tubs.

General Description

Introduction

Overview of Jandy Variable Speed Pumps, their operation, compatibility, and energy efficiency.

Product Specifications

Lists technical specifications like HP, Voltage, Max Watts, Amps, Union Size, and Weight.

Installation Information

Plumbing Installation

Covers preparation, pump location, and pipe sizing recommendations for installation.

Electrical Installation

Details voltage checks, bonding, grounding, and wiring procedures for safe installation.

Conduct Pressure Test

Outlines the procedure for conducting a safe pressure test on the system before operation.

Operation

Start-up Procedure

Guides on how to properly prime and start the Jandy Variable-Speed Pump.

Service & Maintenance

Routine Maintenance

Details tasks for regular pump maintenance, including inspecting and cleaning the filter basket.

Winterizing the Pump

Provides instructions on preparing the pump for winter to prevent freeze damage.

Troubleshooting and Repair

Motor Start and Detection Issues

Troubleshooting steps for motor start or controller detection issues.

Motor Shutdown Issues

Diagnosing and resolving problems where the motor starts but then shuts down.

Blocked Impeller

Procedure for identifying and clearing a blocked pump impeller.

Product Specifications and Technical Data

Exploded Views

Provides an exploded view diagram of the pump for parts identification.

Performance Curves

Presents performance curves showing pump head and flow rate at various speeds.

Jandy VSFHP185DV2A Specifications

General IconGeneral
BrandJandy
ModelVSFHP185DV2A
CategoryWater Pump
LanguageEnglish

Related product manuals