Jandy VS PlusHP - User Manual

Questions and Answers

T
tammyvargasAug 15, 2025
How to improve reduced flow in Jandy VS PlusHP Water Pump?
- R
  rebeccafosterAug 16, 2025
  If your Jandy Water Pump has reduced flow, verify that the skimmer baskets, pump basket, and other screens are clean. Clean them if necessary. Also, check the filter and clean it if needed. Finally, check the valve positions and adjust them as necessary.
J
Jane YuAug 18, 2025
What to do if Jandy Water Pump has no power?
- T
  Todd MartinezAug 18, 2025
  To address the issue of no power to your Jandy Water Pump, ensure that the pump is properly connected to high voltage. Refer to section “3.2 Electrical Installation” for guidance.
C
Christopher LangAug 26, 2025
What to do if my Jandy Water Pump gets hot and shuts off?
- C
  Christopher GrimesAug 26, 2025
  If your Jandy Water Pump gets hot and shuts off periodically, ensure there's enough space around the motor for air circulation to keep it cool. Also, have a qualified electrician check for loose connections and the voltage at the pump motor during operation. The voltage must be within 10% of the motor's data plate rating. If it's not, contact a qualified electrician or your local power service provider.
D
Donald ColemanAug 28, 2025
How to fix air leaks in Jandy VS PlusHP Water Pump?
- F
  fryluisAug 29, 2025
  If you still have air leaks in your Jandy Water Pump, check the suction side piping union. While the pump is running, try tightening the union. If the air leak persists, turn off the pump, loosen both unions, and slide the pump aside. Remove, clean, and reinstall both union o-rings. Reposition the pump and secure the union nuts by hand-tightening them. If the unions still don't seal, gently tighten them with tongue-and-groove pliers, being careful not to overtighten.
Q
qhallSep 1, 2025
What to do if Jandy VS PlusHP Water Pump is leaking water?
- S
  Samuel ThomasSep 1, 2025
  If the Jandy Water Pump is leaking water between the motor and the pump body, this is caused by a damaged or failed mechanical seal. Replace the seal.
C
corymarshSep 8, 2025
How to fix low-voltage wiring in Jandy Water Pump?
- E
  Eugene SmithSep 8, 2025
  To resolve improper low-voltage wiring in your Jandy Water Pump, check the low-voltage wiring between the pump and the controller and correct it if necessary. Refer to section “3.2 Electrical Installation”.
T
Tina ScottSep 12, 2025
How to configure address setting on Jandy VS PlusHP?
- T
  Tyler HansenSep 12, 2025
  To correct an improper pump address setting on your Jandy Water Pump, ensure that pump dip switches 3 and 4 are set properly for your installation. Both should be OFF for use with a Variable-Speed Controller, or set to the proper address when connected to an AquaLink® RS controller, an AquaLink PDA, or an AquaLink Z4. Refer to section “3.2.4.1 Install with AquaLink® controller”.
M
Michelle McdanielNov 21, 2025
Why are there bubbles in my Jandy Water Pump basket?
- C
  Corey HoodNov 21, 2025
  If bubbles are present in the Jandy Water Pump basket, it indicates air is in the system. First, check the pool or spa water level to ensure it's at the proper level, preventing air from being drawn into the suction piping. If the water level is normal, turn off the pump and unlock the lid by turning the locking ring counter-clockwise until 'START' aligns with the ports. Remove the lid and inspect for debris around the lid seal seat or improper installation of the lid seal, as these can cause air leaks. Clean the lid seal and replace it on the lid. Then, put the lid back on the pump housing, align 'START' with the ports, and turn the locking ring clockwise until 'LOCKED' aligns with the ports. Hand-tighten the lid to ensure an airtight seal, avoiding the use of tools. Finally, turn the pum...