EasyManua.ls Logo

Jandy Stealth SHPM - User Manual

Jandy Stealth SHPM
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
Jandy
®
Pro Series Stealth
™
Pumps
Models SHPF and SHPM
H0573800 Rev P
ENGLISH
INSTALLATION AND
OPERATION MANUAL
WARNING
FOR YOUR SAFETY - This product must be installed and serviced by a contractor who is licensed and
qualified in pool equipment by the jurisdiction in which the product will be installed where such state
or local requirements exist. The maintainer must be a professional with sufficient experience in pool
equipment installation and maintenance so that all of the instructions in this manual can be followed
exactly. Before installing this product, read and follow all warning notices and instructions that accompany
this product. Failure to follow warning notices and instructions may result in property damage, personal
injury, or death. Improper installation and/or operation will void the warranty.
Improper installation and/or operation can create unwanted electrical hazard which can
cause serious injury, property damage, or death.
ATTENTION INSTALLER - This manual contains important information about the
installation, operation and safe use of this product. This information should be given to
the owner/operator of this equipment.

Table of Contents

Questions and Answers

  • E
    Edward WangJul 31, 2025
    How to troubleshoot Jandy Water Pump cleaning system not working?
    • E
      Eric ReeseJul 31, 2025
      If your Jandy Water Pump cleaning or circulating system isn't working correctly, start by checking and cleaning the skimmer baskets, pump basket, and other screens. Then, inspect and clean the filter as needed. Also, check and adjust the valve positions. Keep in mind that running multiple pieces of equipment simultaneously, like waterfalls, spa jets, and surface returns, might hinder the cleaning system's performance. Manually inspect the cleaning system to ensure it's adjusted per the manufacturer's guidelines.
  • J
    Justin BanksAug 5, 2025
    Why are there bubbles in my Jandy Stealth SHPM basket?
    • M
      Michael SmithAug 5, 2025
      If bubbles are appearing in the Jandy Water Pump basket, it's likely due to air in the system. First, check that the pool or spa water level is adequate to prevent air from being drawn into the suction piping. If the water level is normal, switch off the pump, remove the lid, and inspect the lid o-ring seat for debris or improper seal installation, either of which can cause air leaks. Clean the lid o-ring, place it on the lid, and hand-tighten the lid to create an airtight seal. Avoid using tools to tighten it. Then, turn the pump back on.
  • D
    davisallisonAug 9, 2025
    What to do if my Jandy Stealth SHPM gets hot and shuts off?
    • C
      Christina BrownAug 9, 2025
      If your Jandy Water Pump gets hot and shuts off periodically, ensure there's enough space around the motor for air circulation to keep it cool. Also, have a qualified electrician inspect for loose connections and verify the voltage at the pump motor while it's running. The voltage should be within 10% of the motor's data plate rating. If it's not, contact a qualified electrician or your local power service provider.
  • J
    John PaulAug 13, 2025
    What to do if Jandy Water Pump pressure is low but there is no air?
    • A
      ashleymyersAug 13, 2025
      If there is no air in your Jandy Water Pump system but the pressure remains low, debris might be lodged in the pump impeller. To address this, first turn off the pump and switch off the circuit breaker to the pump motor. Remove the lid and basket, then inspect the inside of the pump for any debris. Remove any debris you find, then replace the basket and lid. Switch the circuit breaker back on and restart the pump to see if the problem is resolved. If the impeller remains blocked and you cannot remove the debris, you'll need to disassemble the pump to access the impeller's inlet and outlet.
  • R
    Ronald LunaAug 17, 2025
    How to fix Jandy Water Pump air leaks?
    • K
      Kevin EvansAug 17, 2025
      If air leaks persist in your Jandy Water Pump, check the suction side piping union. While the pump is running, attempt to tighten the union. If the leak continues, turn off the pump, loosen both unions, and move the pump aside. Remove, clean, and reinstall both union o-rings. Reposition the pump and secure the union nuts. Hand-tightening should create a seal with clean o-rings. If the unions still leak, gently tighten them using tongue-and-groove pliers, being careful not to overtighten.
  • T
    Tara FigueroaAug 22, 2025
    Why is my Jandy Stealth SHPM leaking water from the motor?
    • A
      Allison RamosAug 22, 2025
      If the Jandy Water Pump is leaking water between the motor and pump body, this is due to a damaged or failed mechanical seal. Have a qualified service technician replace the seal.
  • T
    Tammy MoralesAug 27, 2025
    What causes low pressure in Jandy Stealth SHPM with no debris?
    • J
      Jeffrey WilliamsAug 27, 2025
      If there is no debris blocking the impeller and the pressure is still low in your Jandy Water Pump, it's possible that the pump impeller and diffuser are showing signs of normal wear. In this case, have a qualified service technician inspect and replace the impeller and diffuser as necessary. If the pump is part of a relatively new installation, it could be an electrical problem. Contact a qualified service technician to check for loose electrical connections and verify the voltage at the pump motor while it is in operation. The voltage must be within 10% of the motor's data plate rating. If the voltage is not within 10%, contact a qualified electrician and/or the local power service provider.

Summary

Section 1. IMPORTANT SAFETY INSTRUCTIONS

1.1 Safety Instructions

General electrical and operational safety precautions for installation and use.

1.2 Pool Pump Suction Entrapment Prevention Guidelines

Guidelines to prevent suction entrapment hazards for pool, spa, and hot tub users.

Section 2. General Description

2.1 Introduction

Overview of the manual's content and purpose for Jandy Pro Series SHP Pumps.

2.2 Description

Details on the design and materials used for Jandy Pro Series SHP Pumps.

Section 3. Installation

3.1 Plumbing

Instructions for pump preparation, location selection, and pipe sizing for installation.

3.2 Electrical Installation

Information on voltage checks, bonding, grounding, and wiring for safe pump operation.

3.3 Pressure Testing

Procedures and safety precautions for conducting a pressure test on the pump and system.

Section 4. Operation

4.1 Start-up

Step-by-step guide for starting up the Jandy Pro Series SHP Pumps.

Section 5. Service and Maintenance

5.1 Routine Maintenance

Instructions for performing regular maintenance tasks on the pump.

5.2 Winterizing the Pump

Procedures for properly winterizing the pump to prevent damage from freezing.

Section 6. Troubleshooting

6.1 Troubleshooting

Common symptoms and their possible solutions for pump issues.

Section 7. Product Specifications and Technical Data

7.1 Replacement Parts List

A list of replacement parts with corresponding order numbers for SHPF/SHPM pumps.

7.2 Exploded View

An exploded diagram illustrating the pump components and their assembly.

7.3 SHPF and SHPM Pump Curves

Performance curves showing flow rate vs. total dynamic head for SHPF/SHPM pumps.

7.4 Physical and Operational Specifications

Technical specifications for SHPF and SHPM pump models, including HP, voltage, pipe size, and dimensions.

Jandy Stealth SHPM Specifications

General IconGeneral
ModelSHPM
DimensionsVaries by model
WeightVaries by model
Warranty1 year limited
TypePool Pump
Voltage230V
Flow RateUp to 160 GPM
Port Size2 inches
Speed SettingsSingle Speed
Maximum Flow Rate160 GPM

Related product manuals