Johnson Controls RSH Series User Manual

2
IMPORTANT!
READ BEFORE PROCEEDING!
GENERAL SAFETY GUIDLINES
This equipment is a relatively complicated apparatus.
During installation, operation, maintenance or service,
individuals may be exposed to certain components or
conditions including, but not limited to: refrigerants
materials under p
ressure, rotating components, and
both high and low voltage. Each of these items has the
potential, if misused or handled improperly, to cause
bodily injury or death. It is the obligation and respon
sibilty of operating/service personnel to identify and
re
cognize these inherent hazards, protect themselves,
and proceed safely in completing their tasks. Failure to
comply with any of these requirements could result in
serious damage to the equipment and the property in
SAFETY SYMBOLS
The following symbols are used in this document to alert the reader to areas of potential hazard.
DANGER
indicates an imminently haz
ardous situation which, if not avoided,
will result in death or serious injury.
WARNING indicates a potentially haz
ardous situation which, if not avoided,
could result in death or serious injury.
All wiring must be in accordance with published specifications and must be performed ONLY
by
qualified service personnel. Johnson Controls will not be responsible for damages/problems
resulting from improper connections to the controls or application of improper control signals.
Failure to follow this will void the manufacturers warranty and cause serious damage to prop
erty or injury to persons.
FORM 145.16
JO
IMPORTANT!
READ BEFORE PROCEEDING!
GENERAL SAFETY GUIDLINES
This equipment is a relatively complicated apparatus.
During installation, operation, maintenance or service,
individuals may be exposed to certain components or
conditions including, but not limited to: refrigerants
, oils,
ressure, rotating components, and
both high and low voltage. Each of these items has the
potential, if misused or handled improperly, to cause
bodily injury or death. It is the obligation and respon
-
sibilty of operating/service personnel to identify and
cognize these inherent hazards, protect themselves,
and proceed safely in completing their tasks. Failure to
comply with any of these requirements could result in
serious damage to the equipment and the property in
which it is situated, as well as severe p
death to themselves and people at the site.
This document is intended for use by owner
operating/service personnel. It is expected that this
individual possesses independent training that will en
able them to perform their as
signed tasks properly and
safely. It is essential that, prior to performing any task
on this equipment, this individual shall have read and
understood this document and any referenced materials.
This individual shall also be familiar with and comply with
a
ll applicable governmental standards and regulations
pertaining to the task in question.
SAFETY SYMBOLS
The following symbols are used in this document to alert the reader to areas of potential hazard.
indicates an imminently haz
-
ardous situation which, if not avoided,
will result in death or serious injury.
WARNING indicates a potentially haz
-
ardous situation which, if not avoided,
could result in death or serious injury.
CAUTION identifies a hazard which could
lead to damage to the machine, damage to
other equipment and/or environment
pollution. Usually and instruction will be
given, together with a brief explana
NOTE is used to highlight additional
formation which may be helpful to you.
All wiring must be in accordance with published specifications and must be performed ONLY
qualified service personnel. Johnson Controls will not be responsible for damages/problems
resulting from improper connections to the controls or application of improper control signals.
Failure to follow this will void the manufacturers warranty and cause serious damage to prop
FORM 145.16
-IOM2 (0611)
JOHNSON CONTROLS
which it is situated, as well as severe p
ersonal injury or
death to themselves and people at the site.
This document is intended for use by owner
-authorized
operating/service personnel. It is expected that this
individual possesses independent training that will en
-
signed tasks properly and
safely. It is essential that, prior to performing any task
on this equipment, this individual shall have read and
understood this document and any referenced materials.
This individual shall also be familiar with and comply with
ll applicable governmental standards and regulations
The following symbols are used in this document to alert the reader to areas of potential hazard.
CAUTION identifies a hazard which could
lead to damage to the machine, damage to
other equipment and/or environment
-tal
pollution. Usually and instruction will be
given, together with a brief explana
-tion.
NOTE is used to highlight additional
in-
formation which may be helpful to you.
All wiring must be in accordance with published specifications and must be performed ONLY
qualified service personnel. Johnson Controls will not be responsible for damages/problems
resulting from improper connections to the controls or application of improper control signals.
Failure to follow this will void the manufacturers warranty and cause serious damage to prop
-

Johnson Controls RSH Series Specifications

General

Brand	Johnson Controls
Model	RSH Series
Category	Heat Pump
Language	English