JVC BM-H2000PN - Before Calling for Service; Inoperable Adjustment Controls or Buttons; Abnormal Picture Adjustments with All Controls at Centre; Inoperable Picture Synchronisation

LbL-t
Se
as
Before concluding a problem has occurred, check the following points. If the problem
persists after carrying out the checks, disconnect the power cord from the AC outlet and con-
sult the dealer from whom you purchased the monitor.
| Inoperable adjustment controls
| or buttons.
| Abnormal picture adjustments
| with all controls at centre.
| Inoperable picture
| synchronisation.
Inoperable remote-controlled
| picture adjustments.
Assigned remote control ID
| number operates another
i monitor.
| Inoperabie remote coniroi.
| No sound via audio signal input.
7 No INITIALIZE MENU display.
| Inoperable CNTL-2 external
| control via TALLY/REMOTE
| terminal.
Paints t to be check . cod
| Is MEMORY MODE switched on?
| Deactivate it. |
| Reset to standard settings.
| Is CONTROL LOCK activated?
| Are PICTURE ADJUST menu
| settings changed via remote
| control?
| Is EXT SYNC switched on?
Are the front controls set
| approximately to the maximum
| or minimum?
| ls ID number 00 programmed for
| other monitors?
| Do other monitors indicate a red
| ID number?
| is the 1D number programmed
| for other monitors assigned?
| Does the audio input terminal
| match the video input terminal?
| Are you pressing the w and
| MENU buttons until it appears?
| Is a function applied common to
| CNTL-1 and CNTL-2?
Measures
| If so, the settings may not
| extend any more via remote
| control (although setting levels
| indicated on screen may show a
| slight change).
| Programme an ID number other
| than 00.
| Assign the ID number again.
| Assign the monitor's
| programmed ID number.
| Each audio input terminal is
| linked with a video Input
| terminal.
| Keep pressing these buttons
| until it appears.
| Set other functions to CNTL-2.
Adjustments or settings preset at the factory are shown j in the menus.
For PICTURE ADJUST MENU via remote control, see page 18.
MENU
Menu functions
oS
<MENU> |
| ASPECT RATIO :49 | |
| FELTER.SELECT ‘COMB |
PEAKING FREQ. :2.6MHZ |
PEAKING LEVEL :008 |
AgC SNORMAL |
| COLOR TEMP. 6600
| NTSC SETUP : |
EVE SMPTE
| GH /COMPO(SDI) :AGB
| URE a
MEMORY MODE + MENU
esi “Mode rev revision amenu_
‘MEMORY MODE REVISE:
ASPECT RATIO :43
FILTER SELEGT :COMB
PEAKING FREQ.
:2.6MHZ
| PEAKING LEVEL 30
[ ARG 26
| COLOR TEMP.
NTSC SETUP
ENTER + MENU
at: “up for monitor installation
PSI ZE/CENTERING
STATUS DISPLAY;ON —
. CONTROL LOCK =: OFF
S
| (SET-UP MENU >
|
oa ‘©
Vv + MENU
Menu-function eseiting
‘MENU RESET
Are you sure ?
| |
: |
| a
| |
L ]
Vv +MENU + POWER
“Initialize” menu
iD NUMBE!
ENTER
ie MEMORY MODE AEVISE |
!
PICTURE
pelt
haga
ENTER
»
CONTRAST
ib
|
“ INIT EALECE MENU: : H
FR SET =
(SET-UP MENU: RESET ’
an) |
i
Memory-Mode programming
‘MEMORY MOOE -
Are you aura ?
Ya then
“No then 4 or
i
}
i
j
j
i
eee ee ae |
ae > MENU
Memory-Mode picture adjustments
i] =:
Ee
| geaas
RGB-signal picture
sizsipostioning adjustments
ro
“$178 / CENTER ING: :
i> PH. POSTION
¥. POSITION
i HW. SiZE 7.
i o¥ SEZE
| Oa)
1
|
i
i
é# Oe eee
Whi ie. -palance adjustm nts
jeeere BALANCE.
PRED OF
1 GREEN DRIVE
| BLEE-DBIVE
RED CUTOFE
BREEN CLTOFF
BLUE CUTOFF
a)
‘@sescas:
O epee nae 3 Paneer eect ee
Remote- ‘terminal a settings
REMOTE SELECT :
P INFUT <©NOT USE
ONEL-1 (NOT USE
ENEL +2 : NOT USE
| Oia) a ,
|
1
i
1
|
ID-number programming
| ID NUMBER SET |
| 00 | ENTER
|
: |
ett
Memory-Mode revision
‘MEMORY MODE REVISE:
|
Are you sure 7
‘Yea then]
“No” then Gor R
* SET-UP MENU: RESET
Are you sure?
‘Yeu then G
‘No’ then gor 8
tail
|
|
Menu-function standardisation
21