JVC HR-DD949E - Page 46

46 EN
Storing Cha nnels M a nua lly
Store channels that were not stored during Auto Set Up (Z pg. 4)
or Auto Channel Set (Z pg. 44).
* In Australia and New Zealand, channels cannot be stored
properly even though the following procedure is performed.
TUN ER SET (cont.)
Cha nge Sta tion Cha nnel
Position
SELECT ITEM
1
Press PUSH JO G
%
fi until the item you want to
move begins blinking. Then press O K and the station
name (ID) and its channel (CH) number begin blinking.
SELECT NEW POSITION
2
Press PUSH JO G
%
fi to move the station to the new
channel position, then press O K.
Example: If you moved the station in position 3 to
position 7, the stations originally in positions 4–7 each
move up one space.
● Repeat steps 1 and 2 as necessary.
CLOSE CONFIRMATION
SCREEN
3
Press M EN U .
%
%
%
%
Perform steps 1 and 2 of the previous procedure to access
the Confirmation screen before continuing.
Delete A Cha nnel
SELECT ITEM
1
Press PUSH JO G%
fi
until the item you want to
delete begins blinking.
DELETE CHANNEL
2
Press CAN CEL.
● The item directly beneath the cancelled one moves
up one line.
● Repeat steps 1 and 2 as necessary.
CLOSE CONFIRMATION
SCREEN
3
Press M EN U .
%
%
ACCESS MAIN MENU
1
Press M EN U twice.
ACCESS CONFIRMATION
SCREEN
2
Press PUSH JO G%fi to move the highlight bar (pointer)
to “MANUAL CH SET”, then press OK. The Confirma-
tion screen appears.
SELECT POSITION
3
Press PUSH JO G
%
fi until an open position in
which you want to store a channel begins blinking,
then press OK. The Manual Ch. Set screen appears.
INPUT CHANNEL
4
The number "01" appears blinking beneath "CH".
Press the NU M BER keys to input the channel number
you want to store.
● For fine tuning adjustment, press PUSH JO G until
the item beneath "CH" begins blinking, then press
PU SH JO G%
fi
. While tuning, “F+” or “ F–” appears.
● If necessary, to change the band between CH(regular)
and CC(cable), press PUSH JO G until CH or CC is
blinking, then press PUSH JO G %fi to select the
band.
● When storing a channel that sends scrambled
broadcasts, press PU SH JO G until "OFF" (Decoder
setting) blinks, then press PUSH JO G
%
fi to set
"DECODER" to "ON" ("OFF" is the default setting).
ENTER NEW CHAN NEL
INFORMATION
5
Press O K and the Confirmation screen appears.
● Repeat steps 3 through 5 as necessary.
CLOSE CON FIRMATION SCREEN
6
Press M EN U.
● To input the station name, see page 47.
● To change positions, see "Change Station Channel
Position" (at right).
W hen Receiving A Scrambled Broadcast
Make sure that "AV2 SELECT" is set to "DECODER"
(Z pg. 34).
1– Perform steps 1 and 2 above.
2– Press PUSH JO G%
fi
to select the position of the
channel broadcasting the scrambled programmes, then
press O K three times.
3– Press PUSH JO G until "OFF (Decoder setting)" begins
blinking, and set it to "ON" by pressing PUSH JO G%
fi
.
4– Press O K to access the Confirmation screen.
● Repeat steps 2 – 4 for each additional channel.
5– Press M EN U.
%
%
%
%
fi
%
%
fi
%
Downloaded from: https://www.usersmanualguide.com/