JVC KD-R321 Installation & Connection Manual

2 pages

To Next Page

KD-R322/KD-R321

Installation/Connection Manual

Manuel d’installation/raccordement

0910DTSMDTJEIN

EN, FR

GET0678-010A

[E/EU]

Bracket / Support *

Pocket / Poche

Flat head screws (M5 × 8 mm) /

Vis à tête plate (M5 × 8 mm)*

INSTALLATION / INSTALLATION

When installing the unit without using the sleeve / Lors de l’installation de

l’appareil scans utiliser de manchon

In-dash mounting / Montage encastré

WARNINGS / AVERTISSEMENTS

Removing the unit / Retrait de l’appareil

Release the rear section first... / Ouvrez la section arrière en premier...

Do the required electrical connections. /

Réalisez les connexions électriques.

Bend the appropriate tabs to hold the sleeve

firmly in place. / Tordez les languettes appropriées

pour maintenir le manchon en place.

Install the unit at an angle

of less than 30˚. / Installez

l’appareil avec un angle de

moins de 30˚.

* Not supplied for this unit.

* Non fourni avec cet appareil.

Part list / Liste de pièces

Control panel / Panneau de

commande (×1)

Sleeve / Manchon (×1)

Trim plate / Plaque d’assemblage (×1)

Power cord / Cordon d’alimentation

(×1)

Handles / Poignées (×2)

• You need the installation kits which corresponds to your car.

• If you have any questions or require information regarding installation kits, consult your JVC IN-CAR

ENTERTAINMENT dealer or a company supplying kits.

• The unit can only be installed in a car with a 12 V DC power supply, negative ground.

• Disconnect the battery’s negative terminal and make all electrical connections before installing the unit.

• Connect speakers with a maximum power of more than 50 W (impedance of 4 Ω to 8 Ω). Otherwise,

change the <AMP GAIN> setting. (See page 12 of the INSTRUCTIONS.)

• Insulate unconnected wires with vinyl tape or other similar material. To prevent a short circuit, do not

remove the caps on the ends of the unconnected wires or the terminals.

• If the fuse blows, first make sure the wires are not touching to cause a short circuit, then replace the old

fuse with one that has the same rating.

• Install this unit in the console of your vehicle.

• Mount the unit so that the mounting angle is 30° or less.

• Be sure to ground this unit to the car's chassis again after installation.

• After the unit is installed, check whether the brake lamps, blinkers, wipers, etc. on the car are working

properly.

• Do not touch the metal part of this unit during and shortly after the use of the unit. Metal part such as the

heat sink and enclosure become hot.

• Vous avez besoin des kits d’installation correspondants à votre voiture.

• Si vous avez des questions ou avez besoin d’information sur des kits d’installation, consulter votre revendeur

d’autoradios JVC ou une compagnie d’approvisionnement.

• L’appareil peut uniquement être installé dans une voiture avec une alimentation de 12 V CC, à masse négative.

• Déconnectez la borne négative de la batterie et réaliser toutes les connexions avant d’installer l’appareil.

• Connectez des enceintes avec une puissance maximum de 50 W (impédance de 4 Ω à 8 Ω). Sinon, changez le

réglage <AMP GAIN>. (Voir la page 12 du MANUEL D’INSTRUCTIONS.)

• Isolez les câbles non-connectés avec un ruban de vinyle ou d’un autre matériel similaire. Pour éviter les courts-

circuits, ne retirez pas non plus les capuchons à l’extrémité des câbles non-connectés ou des prises.

• Si un fusible saute, assurez-vous d’abord que les câbles n’ont pas causé de court-circuit puis remplacez le vieux

fusible par un nouveau de même valeur.

• Installez cet appareil dans la console de votre véhicule.

• Monter l’unité de façon à ce que l’angle de montage soit de 30˚ ou moins.

• Assurez-vous de raccorder de nouveau la mise à la masse de cet appareil au châssis de la voiture après

l’installation.

• Après avoir installé l’appareil, vérifiez si les lampes de frein, les indicateurs, les clignotants, etc. de la voiture

fonctionnent correctement.

• Ne touchez pas la partie métallique de cet appareil pendant ou juste après son utilisation. Les parties métalliques,

comme le dissipateur de chaleur et le boîtier, deviennent chaudes.

PRECAUTIONS on power supply and speaker connections

• DO NOT connect the speaker leads of the power cord to the car battery; otherwise, the unit will be

seriously damaged.

• BEFORE connecting the speaker leads of the power cord to the speakers, check the speaker wiring in

your car.

PRECAUTIONS sur l’alimentation et la connexion des enceintes

• NE CONNECTEZ PAS les fils d’enceintes du cordon d’alimentation à la batterie; sinon, l’appareil serait

sérieusement endommagé.

• AVANT de connecter les fils d’enceintes du cordon d’alimentation aux enceintes, vérifiez le câblage des enceintes

de votre voiture.

ENGLISH / FRANÇAIS

Install_KD-R322_010A_f.indd 1Install_KD-R322_010A_f.indd 1 9/21/10 4:47:39 PM9/21/10 4:47:39 PM

Other manuals for JVC KD-R321

Instructions17 pages

Instruction Manual29 pages

Manual17 pages

Questions and Answers:

C
Charles BeckerAug 29, 2025
What does 'PLEASE' and 'EJECT' mean on my JVC Car Receiver display?
- J
  Jean RobinsonAug 29, 2025
  If “PLEASE” and “EJECT“ appear alternately on the display of your JVC Car Receiver, press 0, then insert a disc correctly.
J
Jeffrey SanchezAug 29, 2025
Why is there static noise while listening to the radio on my JVC Car Stereo System?
- R
  reyesbrendaAug 29, 2025
  If you are experiencing static noise while listening to the radio, make sure that the aerial is firmly connected.
J
jimenezchristopherAug 30, 2025
What to do if disc sound is sometimes interrupted in JVC Car Stereo System?
- D
  Danielle GibsonAug 30, 2025
  If the disc sound is sometimes interrupted in your JVC Car Stereo System, consider the following: * Stop playback while driving on rough roads. * Try changing the disc. * Check the cords and connections.
M
Melissa JordanAug 25, 2025
Why is there no sound from my JVC Car Stereo System speakers?
- M
  matthewbennettAug 25, 2025
  If you can't hear any sound from the speakers, try these steps: First, adjust the volume to a suitable level. Second, ensure that the unit is not muted or paused. Finally, check the cords and connections to make sure they are properly connected.
J
Jennifer ChangAug 31, 2025
Why can't my JVC Car Stereo System play CD-R/CD-RW or skip tracks?
- A
  amy57Aug 31, 2025
  If your JVC Car Stereo System cannot play CD-R/CD-RW discs or skip tracks, make sure you are using a finalized CD-R/CD-RW. Finalize the disc with the component you used for recording.
S
Sheryl WelchSep 1, 2025
What does 'PLEASE' and 'EJECT' alternately mean on my JVC Car Stereo System?
- F
  Francisco BowmanSep 1, 2025
  If “PLEASE” and “EJECT“ appear alternately on the display of your JVC Car Stereo System, press the 0 button, then insert the disc correctly.
B
Beth ParkerSep 1, 2025
What does 'IN DISC' mean on my JVC Car Stereo System?
- L
  Lori OrtizSep 1, 2025
  If “IN DISC” appears on the display of your JVC Car Stereo System, it indicates that the disc cannot be ejected properly. Make sure nothing is blocking the loading slot.
M
Mark PerrySep 2, 2025
Why can't my JVC Car Stereo System play back a disc?
- J
  jeffreyhillSep 2, 2025
  If your JVC Car Stereo System cannot play back a disc, make sure to use a disc with MP3/WMA tracks recorded in a format compliant with ISO 9660 Level 1, Level 2, Romeo, or Joliet. Also, add the extension code or to the file names.
J
Julia GriffithSep 2, 2025
Why is noise generated on my JVC Car Stereo System?
- M
  Matthew GreenSep 3, 2025
  If noise is generated on your JVC Car Stereo System, try skipping to another track or changing the disc.
M
Michele MorrisonSep 3, 2025
Why is sound sometimes interrupted when using auxiliary input on my JVC Car Stereo System?
- A
  Amanda PierceSep 3, 2025
  If the sound is sometimes interrupted while listening to an external component connected to the auxiliary input jack on your JVC Car Stereo System, check to be sure the recommended stereo mini plug is used for connection.

JVC KD-R321 Specifications

General

MP3 playback	Yes
Audio formats supported	MP3, WMA
Preset stations quantity	24
Output power	200 W
Ready for iPod	-
Audio output channels	4.0 channels
Maximum power per channel	50 W
I/O ports	2 AUX In