15
Sound Adjustments
Front Panel
Remote Control
CONTROL
DOWN UP
SUBWOOFER +/–
SOUND
Display
CONTROL UP 5/DOWN ∞ADJUSTINPUT ATT
Once each of following settings has been adjusted, this receiver
memorizes the adjustment for each source.
Attenuating the Input Signal
When the input level of the analog source is too high, the sounds
will be distorted. If this happens, you need to attenuate the input
signal level to prevent the sound distortion.
1
Press and hold INPUT ATT (INPUT
ANALOG) so that the INPUT ATT
indicator lights up on the display.
• Each time you press and hold the button, the Input Attenuator
mode turns on (“INPUT ATT ON”) or off (“INPUT
NORMAL”).
Adjusting the Front Speakers
Output Balance
If the sounds you hear from the front right and left speakers are
unequal, you can adjust the speakers output balance.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1
again.
1
Press ADJUST repeatedly until
“BALANCE” (with the current setting)*
appears on the display.
* “CNTR” (Center) is the initial setting. If you have already
changed the setting, another setting will be shown.
2
Press CONTROL UP 5/DOWN ∞
to adjust the balance.
• Pressing CONTROL UP 5 decreases the
left channel output from “CNTR” (Center) to
“L–21.”
• Pressing CONTROL DOWN ∞ decreases
the right channel output from “CNTR” (Center) to “R–21.”
Adjusting the Tone
You can adjust the bass and treble sounds as you like.
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1
again.
Remote
NOT
INPUT ANALOG
INPUT ATT
Remote
NOT
ADJUST SET
CONTROL
DOWN UP
Remote
NOT
FM MODE
A/V CONTROL
RECEIVER
STANDBY/ON
AUDIO
TV
VCR
DVD
TEST
EFFECT
MENU
ENTER
RETURN
SOUND
SLEEP
CENTER
REAR L
SUBWOOFER
PTY–PTY SEARCH–PTY
DISPLAY MODE
CD
–
DISC
REC PAUSE
TAPE/CDR CD DVD
FM/AM
FM MODE
DIMMER TV/VIDEO
SURROUND
ON/OFF
MODE
MUTING
VCR CH
TV CH
TV VOLUME
VOLUME
TV SOUND VCR
ANALOG
/DIGITAL
REAR R
1
4
7/P
10
2
5
8
0
3
6
9
10
REMOTE CONTROL RM-SRX5022R
REW
FF
TA/NEWS/INFO
100
1
Press ADJUST repeatedly until “BASS”
or “TREBLE” (with the current
setting)* appears on the display.
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
BASS : To adjust the bass (–10 to +10).
TREBLE : To adjust the treble (–10 to +10).
2
Press CONTROL UP 5/DOWN ∞ to
adjust the bass or treble sounds level.
• Each time you press the button, the sound
level changes by ±2 steps.
Adjusting the Subwoofer Output Level
You can adjust the subwoofer output level if you have connected a
subwoofer and set the subwoofer information correctly—“YES.”
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
1
again.
1
Press ADJUST repeatedly until
“SUBWFR (Subwoofer)” (with the
current setting)* appears on the
display.
* “0” is the initial setting. If you have already changed the
setting, another number (level) will be shown.
2
Press CONTROL UP 5/DOWN ∞ to
adjust the subwoofer output level
(–10 to +10).
From the remote control:
1
Press SOUND.
The 10 keys are activated for sound adjustments.
2
Press SUBWOOFER +/– to adjust
the subwoofer output level (–10 to
+10).
Note:
Subwoofer output level cannot be adjusted when using headphones.
ADJUST SETTI
DVD VCR TV SOUND
ADJUST
RX-5022R AUDIO/VIDEO CONTROL RECEIVER
SETTING
CONTROL
DOWN UP
CD TAPE/CDR
SOURCE NAME
INPUT DIGITALINPUT ANALOG
SPEAKERS ON/OFF
SURROUND MODE
PHONES
SURROUND ON/OFF
FM/AM TUNING
STANDBY
FM/AM PRESET FM MODE
MEMORY
INPUT ATT
FM/AM
STANDBY/ON
LC
S.WFR
LS RS
CH-
S
LFE
SPK
PRO LOGIC ΙΙ DSP H.PHONE
AUTO MUTING
TUNED
STEREO
TA NEWS INFO
VOLUME
INPUT ATT RDS
SLEEP
DIGITAL AUTO
ANALOG
DIGITAL
LINEAR PCM
R
UP
DOWN
UP
DOWN
MASTER VOLUME
PTY SEARCH TA/NEWS/INFO DISPLAY MODE
DIMMER
CONTROL
DOWN UP
ADJUST SETTI
SOUND
EN08-20.RX-5022RSL[B]_f 02.1.16, 5:33 PM15
To Next Page
Loading...
Need help?
General
