JVC RX-F10S User Manual (English)

Other manuals for JVC RX-F10S

Instructions88 pages

Schematic Diagrams18 pages

Questions and Answers:

M
Michael RodriguezAug 31, 2025
How to fix continuous hiss during FM reception on my JVC RX-F10S Receiver?
- K
  Kelly MartinAug 31, 2025
  If you are experiencing continuous hiss or buzzing during FM reception on your JVC Receiver, the incoming signal may be too weak. Try connecting an outdoor FM antenna or contact your dealer. The station might also be too far away, so select another station. Ensure that you are using the correct antenna; check with your dealer to confirm. Also, verify that the antennas are connected properly.
J
Jon NelsonAug 30, 2025
What to do if my JVC RX-F10S Receiver shows 'OVER HEAT' and turns off?
- H
  hansenlauraAug 30, 2025
  If the JVC Receiver displays “OVER HEAT” and turns off, it indicates the receiver is overloaded due to high volume or long usage. Turn the receiver on again. If it turns off soon after, unplug the power cord and consult your dealer.
T
timothymatthewsAug 28, 2025
Why does my JVC RX-F10S turn off by itself?
- S
  Steven BergerAug 29, 2025
  If your JVC Receiver turns off and enters standby mode, it could be due to several reasons. The speakers might be overloaded because of high volume, so stop the playback source. Alternatively, there might be a short circuit at the speaker terminals; in this case, check the speaker wiring. If the wiring is not short-circuited, contact your dealer. It is also possible that the receiver is overloaded because of high voltage, if so, consult your dealer after unplugging the power cord.
A
Anita HarrisAug 27, 2025
What to do if there is no sound from my JVC Receiver speakers?
- S
  Sheila RobertsAug 27, 2025
  If there is no sound coming from the speakers of your JVC Receiver, first ensure the speaker signal cables are correctly connected. Check all audio connections to confirm they are properly set up. Make sure that you have selected the correct source on your receiver. Verify that muting is not activated by pressing the MUTING button. Confirm that the input mode (analog or digital) is correctly selected. Finally, check if TV Direct is activated and deactivate it if necessary.
A
aleeAug 26, 2025
Why does my JVC Receiver remote control not operate as I intend?
- C
  Cheryl LarsonAug 27, 2025
  The remote control may not be ready for your intended operation. Set the mode selector correctly, then press the corresponding source selecting button or SOUND before operation.
R
Rhonda HoltAug 25, 2025
What to do if my JVC RX-F10S remote control does not work?
- J
  Justin EscobarAug 26, 2025
  If your JVC Receiver remote control isn't working, consider these potential causes: * There may be an obstruction hiding the remote sensor on the receiver. Remove any obstructions. * The batteries might be weak. Replace the batteries. * The mode selector could be set to the incorrect position. Ensure the mode selector is in the proper position.
F
Frank BallardAug 23, 2025
Why is my JVC RX-F10S Receiver remote control not operating correctly?
- J
  Jacob JonesAug 25, 2025
  If the remote control of your JVC Receiver does not operate as intended, it might not be ready for your intended operation. Set the mode selector correctly, then press the corresponding source selecting button or SOUND before operation.

JVC RX-F10S Specifications

General

Weight	10.2kg
Preset Stations	30
Power output	100 watts per channel
Total harmonic distortion	0.8% (1 kHz)
Input sensitivity	200 mV/47 kOhms (line)
Signal to noise ratio	95dB (line)
Output	200mV (line)
Video Connections	composite
Amplifier Type	Digital
RMS Power per Channel (8 Ohms, 20Hz-20kHz)	100W
THD	0.8%
Signal-to-Noise Ratio	100dB (line)
Tuner Type	Digital