To Next Page
N
Nicole BarnettAug 19, 2025
What to do if Kärcher B80W Floor Machine battery depleted?
- RRichard JohnsonAug 19, 2025
If the Kärcher Floor Machine indicates a depleted battery, charge the battery.
What to do if Kärcher B80W Floor Machine battery depleted?
If the Kärcher Floor Machine indicates a depleted battery, charge the battery.
What to do if Kärcher B80W Floor Machine shows 'Battery depleted!!!'?
If your Kärcher Floor Machine displays 'Battery depleted!!!', charge the battery.
What to do if Kärcher B80W has insufficient vacuum performance?
If you notice insufficient vacuum performance with your Kärcher Floor Machine, take these steps: Clean the seals between the dirt water reservoir and its cover, ensuring they are tight, and replace if needed. Clean the fluff filter and the vacuum lips on the vacuum bar, replacing if necessary. Check the suction hose for blockages and tightness, cleaning or replacing as needed. Ensure the cover on the dirt water discharge hose is closed and verify the setting of the vacuum bar.
How to improve cleaning results with Kärcher B80W?
To improve cleaning results with your Kärcher Floor Machine, try the following: Set or adjust the contact pressure. Check the brushes for wear and replace them if needed. Use the appropriate brush type for the kind of dirt you're dealing with. For appliances with brush rollers FACT, set to "Power Clean". Empty the waste container on the BR head.
What to do if Kärcher B80W Floor Machine has insufficient water quantity?
If your Kärcher Floor Machine isn't dispensing enough water, check the fresh water level and refill the tank if it's low. Also, inspect the fresh water filter and clean it if necessary. Finally, check the hoses for any blockages and clean them if needed.
What to do if Kärcher B80W does not move?
If your Kärcher Floor Machine isn't moving, check to see if the parking brake has been triggered.
What does 'Driving lever active!' mean on Kärcher B80W Floor Machine?
If your Kärcher Floor Machine displays 'Driving lever active!', it means the driving lever was not in the center position when the appliance was switched on. Turn off the appliance, move the driving lever to the center position, and then turn the appliance back on.
What to do if Kärcher Floor Machine says 'Refill detergent!'?
If your Kärcher Floor Machine displays 'Refill detergent!', install a full detergent container.
What does 'Brush overload!' mean on Kärcher B80W?
If your Kärcher Floor Machine displays 'Brush overload!', it means the maximum brush power has been exceeded for more than 5 seconds. Check and adjust the contact pressure at the brush head.
What does 'Gas pedal !!!' mean on Kärcher Floor Machine?
If your Kärcher Floor Machine displays 'Gas pedal !!!', it indicates a driving lever fault during operation. Release the driving lever, switch the appliance off and back on again, and then check the driving lever.
General| Model | B80W |
|---|---|
| Category | Floor Machine |
| Working width, brush | 800 mm |
| Working width, vacuum | 800 mm |
| Brush Width | 800 mm |
| Battery Voltage | 24 V |
| Battery Capacity | 100 Ah |
| Noise Level | 70 dB(A) |
| Brush speed | 150 rpm |
| Battery | 24 V |
| Charging Time | 8 - 10 h |
| Working Speed | Up to 6 km/h |
| Type | Battery-powered scrubber dryer |
Safety devices serve to protect the user and must not be rendered inoperational.
Indicates useful tips and important information about the product.
Details about the appliance's drive system, including voltage and motor configuration.
Describes the brush head options (roller or disc) and their operation.
Explains the fresh and waste water reservoirs and their functions.
Diagram and labels for the front components of the appliance.
Details the operating elements, displays, and control panel functions.
Explains how to use the operator menu, setup menu, and debug mode.
Instructions for adjusting the vacuum bar for optimal cleaning results.
Steps for safely removing the suction turbine from the appliance.
Procedures for replacing brush heads and their components.
Instructions for removing, installing, and tensioning the drive belt.
Diagnosing and resolving faults indicated on the appliance display.
