Keysight E5071C User Manual

14 | Keysight | E5071C Network Analyzer - Conguration Guide
1. Order the 82357B USB/GPIB interface to control a power meter by the
E5071C.
2. To use the U200x USB power sensors for source power calibration, the
E5071C ENA rmware version A.09.2x or higher is required.
Additional Accessories
Power limiters
– N9355B power limiter, 10 dBm limiting threshold,
10 MHz to 18 GHz, Type-N
– N9356B power limiter, 25 dBm limiting threshold,
10 MHz to 18 GHz, Type-N
– N9355C power limiter, 10 dBm limiting threshold,
10 MHz to 26.5 GHz, 3.5 mm
– N9356C power limiter, 25 dBm limiting threshold,
10 MHz to 26.5 GHz, 3.5 mm
DC blocks
– N9398C DC block, 16 V maximum working voltage,
50 kHz to 26.5 GHz, 3.5 mm
– N9399C DC block, 50 V maximum working voltage,
700 kHz to 26.5 GHz, 3.5 mm
– 11742A, 50 V maximum working voltage, 45 MHz to 26.5 GHz,
3.5 mm
Ampliers
– 87405B pre-amplier, 22 dB gain, 10 MHz to 4 GHz
– 87405C pre-amplier, 25 dB gain, 100 MHz to 18 GHz
– 87415A amplier, 25 dB gain, 2 to 8 GHz
– 83006A amplier, 20 dB gain, 10 MHz to 26.5 GHz
Attenuators
– 8491A xed attenuator, DC to 12.4 GHz, Type-N
– 8493A xed attenuator, DC to 12.4 GHz, SMA
RF & microwave switches
– N1810TL SPDT switch, terminated, DC to 26.5 GHz
– N1810UL SPDT switch, unterminated, DC to 26.5 GHz
– 87104B SP4T switch, terminated, DC to 20 GHz
– 87106B SP6T switch, terminated, DC to 20 GHz
– 87222C transfer switch, DC to 26.5 GHz
– L7104B SP4T switch, terminated, DC to 20 GHz
– L7106B SP6T Switch, terminated, DC to 20 GHz
– L7222C transfer switch, DC to 26.5 GHz
– P9400C solid state PIN diode transfer switch, 100 MHz to 18 GHz
– P9402C SPDT solid state PIN diode switch, 100 MHz to 18 GHz
– P9404C SP4T solid state PIN diode switch, 100 MHz to 18 GHz
– U9397C SPDT solid state FET hybrid switch, 300 kHz to 18 GHz
– U9400C solid state FET hybrid transfer switch, 300 KHz to 18 GHz
Power meters and sensors
1
Recommended for source output power calibration.
– E4416A
1
single-channel EPM-P series power meter
– E4417A
1
dual-channel EPM-P series power meter
– E4418B
1
single-channel EPM series power meter
– E4419B
1
dual-channel EPM series power meter
– N1911A
1
single-channel P-series power meter
– N1912A
1
dual-channel P-series power meter
– 8482A power sensor, 100 kHz to 4.2 GHz, Type-N (m), 100 mW
– E9304A-H18 power sensor, 9 kHz to 18 GHz, Type-N (m), 100 mW
– E4412A CW power sensor, 10 MHz to 18 GHz, Type-N (m), 200 mW
– E4413A CW power sensor, 50 MHz to 26.5 GHz, 3.5 mm (m), 200 mW
– N1921A power sensor 50 MHz to 18 GHz, Type-N (m)
– N1922A power sensor 50 MHz to 40 GHz, 2.4 mm (m)
– U2000A/B/H
2
USB power sensor, 10 MHz to 18 GHz, Type-N (m)
– U2001A/B/H
2
USB power sensor, 10 MHz to 6 GHz, Type-N (m)
– U2002A/H
2
USB power sensor, 50 MHz to 24 GHz, 3.5 mm (m)
– U2004A
2
USB power sensor, 9 kHz to 6 GHz, Type-N (m)
Probes
– N1021B 18 GHz differential TDR/TDT passive probe kit
– 85024A high-frequency probe, 300 kHz to 3 GHz
General accessories
System racks
– 1CN005A handle kit, may be ordered as option 1CN (two included)
– 1CM015A rack mount kit, for use without handles: may be ordered as
option 1CM
– 1CP009A rack mount kit, for use with previously supplied handles;
may be ordered as option 1CP
– E3663AC rack mount rail kit, for use with 1CM015A or 5188-4430
– 1181BZ test mobile system cart
Interface cables
The following GPIB cables can be used to connect the network
analyzer with an external device such as a computer
– 10833A GPIB cable, 1.0 m (3.3 ft)
– 10833B GPIB cable, 2.0 m (6.6 ft)
– 10833C GPIB cable, 4.0 m (13.1 ft)
– 10833D GPIB cable, 0.5 m (1.6 ft)
– 82357B GPIB to USB interface, necessary to control a power meter or
signal generator with the E5071C.
Monitors
– XGA-compatible monitor
Printers
– USB printers with Microsoft Windows printer driver
Other
– 8710-1764 WRENCH - TORQUE 8 IN/LB, 20 MM OPEN END

Keysight E5071C Specifications

General

Brand	Keysight
Model	E5071C
Category	Measuring Instruments
Language	English