13 | Keysight | E5071C Network Analyzer - Conguration Guide
1. For this option order K281C-012.
For devices with 75 Ω Type-N connectors
Mechanical calibration kits
– 85036B DC to 3 GHz, includes:
00909-60019 75 Ω Type-N (m) broadband load
00909-60020 75 Ω Type-N (f) broadband load
85036-60012 75 Ω Type-N (m) short
85036-60011 75 Ω Type-N (f) short
85032-60007 75 Ω Type-N (m) open
85032-20001 75 Ω Type-N (f) open body
85036-60010 75 Ω Type-N (f) open center conductor
extender
85036-60013 75 Ω Type-N (m) to (m) adapter
85036-60014 75 Ω Type-N (f) to (f) adapter
85036-60015 75 Ω Type-N (m) to (f) adapter
– 85036E DC to 3 GHz, includes:
00909-60019 75 Ω Type-N (m) broadband load
85036-60016 75 Ω Type N (m) combined open/short
Adapters
– 11852B Minimum-loss pad
Option 11852B-004 Type-N connectors, 50 Ω (m) to 75 Ω (f)
Calibration must be done with a 75 Ω calibration kit
using an 11852B minimum-loss pad, and impedance conversion
to 75 Ω using the ENA’s xture simulator function is required.
For devices with waveguide
Mechanical calibration kits
X Band
– X11644A standard, WR-90: 8.2 to 12.4 GHz.
Includes:
00896-60008 X-band standard section
00910-60003 X-band termination
11644-20018 X-band short
11644-20021 X-band shim
– 85132F cable set (set of 2, exible 7 mm to 3.5 mm, 62.9 cm
each, 24.75 inches each)
– 85135F cable set (set of 2 , exible, 7 mm to 2.4 mm, 53 cm
each, 21 inches each)
– X281C adapter (included in calibration kit): WR-90 to 7 mm
P Band
– P11644A standard, WR-62: 12.4 to 18 GHz.
Includes:
00896-60007 P-band standard section
00910-60002 P-band termination
11644-20017 P-band short
11644-20020 P-band shim
– 85132F cable set (set of 2, exible, 7 mm to 3.5 mm, 62.9 cm
each, 24.75 inches each)
– 85135F cable set (set of 2, exible, 7 mm to 2.4 mm, 53 cm
each, 21 inches each)
– P281C adapter (included in calibration kit): WR-62 to 7 mm
K Band
– K11644A standard, WR-42: 18 to 26.5 GHz.
Includes:
00896-60006 K-band standard section
00910-60001 K-band termination
11644-20016 K-band short
11644-20019 K-band shim
– 85134F cable set (set of 2, exible, 3.5 mm to 2.4 mm, 53 cm
each, 21 inches each)
– K281C adapter (included in calibration kit):
WR-42 to 3.5 mm (f)
Option 012
1
WR-42 to 3.5 mm (m)