Keysight N6700C Series

To Next Page

To Previous Page

Staircase

Back to ARB Commands

[SOURce:]ARB:CURRent:STAircase:END[:LEVel] <value>, (@<chanlist>)

[SOURce:]ARB:CURRent:STAircase:END[:LEVel]? [MIN|MAX,] (@<chanlist>)

[SOURce:]ARB:VOLTage:STAircase:END[:LEVel] <value>, (@<chanlist>)

[SOURce:]ARB:VOLTage:STAircase:END[:LEVel]? [MIN|MAX,] (@<chanlist>)

[SOURce:]ARB:POWer:STAircase:END[:LEVel] <value>, (@<chanlist>)

[SOURce:]ARB:POWer:STAircase:END[:LEVel]? [MIN|MAX,] (@<chanlist>)

[SOURce:]ARB:RESISTANCE:STAircase:END[:LEVel] <value>, (@<chanlist>)

[SOURce:]ARB:RESISTANCE:STAircase:END[:LEVel]? [MIN|MAX,] (@<chanlist>)

Specifies the ending current, voltage, power, or resistance level after the staircase occurs.

[SOURce:]ARB:SEQuence:STEP:CURRent:STAircase:END[:LEVel] <value>, <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:CURRent:STAircase:END[:LEVel]? [MIN|MAX,] <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:VOLTage:STAircase:END[:LEVel] <value>, <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:VOLTage:STAircase:END[:LEVel]? [MIN|MAX,] <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:POWer:STAircase:END[:LEVel] <value>, <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:POWer:STAircase:END[:LEVel]? [MIN|MAX,] <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:RESISTANCE:STAircase:END[:LEVel] <value>, <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:RESISTANCE:STAircase:END[:LEVel]? [MIN|MAX,] <step#>, (@<chanlist>)

Specifies the ending current, voltage, power, or resistance level after the staircase occurs for Arb

sequence steps.

The difference between the start level and the end level is divided equally among the

number of steps.

Parameter Typical Return

Current: 0 - maximum|MIN|MAX, *RST MIN

Voltage: 0 - maximum|MIN|MAX, *RST MIN

Power: 0 - maximum|MIN|MAX, *RST MIN

Resistance: 0 - maximum|MIN|MAX, *RST MIN

Values are range and module-rating dependent.

Step 0 - 99, *RST 0 (none)

Programs an end level current: ARB:CURR:STA:END 2,(@1)

Programs an end level voltage: ARB:VOLT:STA:END 20,(@1)

Programs an end level power: ARB:POW:STA:END 20,(@1)

Programs an end level resistance: ARB:RESISTANCE:STA:END 50,(@1)

Programs an end level current for step 0: ARB:SEQ:STEP:CURR:STA:END 2, 0,(@1)

5 SCPI Programming Reference

206 Keysight N6700C Operating and Service Guide

Keysight N6700C Series - Page 206