Keysight N6700C Series

To Next Page

To Previous Page

Parameter Typical Return

Current: 0 - maximum|MIN|MAX, *RST MIN

Voltage: 0 - maximum|MIN|MAX, *RST MIN

Power: 0 - maximum|MIN|MAX, *RST MIN

Resistance: 0 - maximum|MIN|MAX, *RST MIN

Values are range and module-rating dependent.

Step 0 - 99, *RST 0 (none)

Programs a start- and end-level current: ARB:CURR:TRAP:STAR 1,(@1)

Programs a start- and end- level voltage: ARB:VOLT:TRAP:STAR 1,(@1)

Programs a start- and end- level power: ARB:POW:TRAP:STAR 1,(@1)

Programs a start- and end-level resistance: ARB:RESISTANCE:TRAP:STAR 10,(@1)

Programs a start- and end-level for step 0: ARB:SEQ:STEP:CURR:TRAP:STAR 1, 0,(@1)

[SOURce:]ARB:CURRent:TRAPezoid:STARt:TIMe <value>, (@<chanlist>)

[SOURce:]ARB:CURRent:TRAPezoid:STARt:TIMe? [MIN|MAX,] (@<chanlist>)

[SOURce:]ARB:VOLTage:TRAPezoid:STARt:TIMe<value>, (@<chanlist>)

[SOURce:]ARB:VOLTage:TRAPezoid:STARt:TIMe? [MIN|MAX,] (@<chanlist>)

[SOURce:]ARB:POWer:TRAPezoid:STARt:TIMe<value>, (@<chanlist>)

[SOURce:]ARB:POWer:TRAPezoid:STARt:TIMe? [MIN|MAX,] (@<chanlist>)

[SOURce:]ARB:RESISTANCE:TRAPezoid:STARt:TIMe<value>, (@<chanlist>)

[SOURce:]ARB:RESISTANCE:TRAPezoid:STARt:TIMe? [MIN|MAX,] (@<chanlist>)

Specifies the delay in seconds after the trigger is received, but before the rising ramp occurs.

[SOURce:]ARB:SEQuence:STEP:CURRent:TRAPezoid:STARt:TIMe <value>, <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:CURRent:TRAPezoid:STARt:TIMe? [MIN|MAX,] <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:VOLTage:TRAPezoid:STARt:TIMe <value>, <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:VOLTage:TRAPezoid:STARt:TIMe? [MIN|MAX,] <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:POWer:TRAPezoid:STARt:TIMe <value>, <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:POWer:TRAPezoid:STARt:TIMe? [MIN|MAX,] <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:RESISTANCE:TRAPezoid:STARt:TIMe <value>, <step#>, (@<chanlist>)

[SOURce:]ARB:SEQuence:STEP:RESISTANCE:TRAPezoid:STARt:TIMe? [MIN|MAX,] <step#>, (@<chanlist>)

Specifies the delay in seconds after the trigger is received, but before the rising ramp occurs for Arb

Sequence steps.

Parameter Typical Return

0 – 262.144 | MIN | MAX, *RST 0 <start time>

Step 0 - 99, *RST 0 (none)

Programs a start time for the current trapezoid: ARB:CURR:TRAP:STAR:TIM 1,(@1)

Programs a start time for the voltage trapezoid: ARB:VOLT:TRAP:STAR:TIM 1,(@1)

Programs a start time for the power trapezoid: ARB:POW:TRAP:STAR:TIM 1,(@1)

Programs a start time for the resistance trapezoid: ARB:RESISTANCE:TRAP:STAR:TIM 1,(@1)

Programs a start time for step 0: ARB:SEQ:STEP:CURR:TRAP:STAR:TIM 1, 0,(@1)

Keysight N6700C Operating and Service Guide 217

5 SCPI Programming Reference

Keysight N6700C Series - Page 217