KVM KVM6000 Series - P4 Input Terminals Function

- 20 -
- 21 -
KVM6000
Function Code Table KVM6000 Function Code Table
P3 V/F Control Parameters
Function
Code
P3-00
P3-01
P3-02
P3-03
P3-04
P3-05
P3-06
P3-07
P3-08
P3-09
Parameter Name
V/F curve
selection
Multi-point
V/F frequency1
(F1)
Multi-point
V/F voltage1 (V1)
Multi-point
V/F frequency2
(F2)
Multi-point
V/F voltage2 (V2)
Multi-point
V/F frequency3
(F3)
Multi-point
V/F voltage3 (V3)
V/F Torque boost
Cut-off
frequency of
torque boost
V/F slip
compensation
Address
0300H
0302H
0301H
0304H
0303H
0306H
0305H
0307H
0308H
0309H
Setting Range
0: Linear V/F 2: Square V/F
3: 1.2-power V/F 4: 1.4-power V/F
6: 1.6-power V/F 8: 1.8-power V/F
9: Reserved 10: V/F complete separation
11: V/F half separation
0.00～P3-03
0.0～P3-04
P3-01～P3-05
P3-02～P3-06
P3-03～maximum frequency
P3-04～100%
0.1～30.0%
0.00～maximum frequency
0～200.0%
Default
0
1.00Hz
3.0%
25.00Hz
50.0%
50.00Hz
100%
1.0%
50.00Hz
0.0%
P2-22
2～10
10～500%
2
100%
P2-23
0216H
0217H
Field weakening
automatic
adjustment gain
Field weakening
integral multiple
P3-10
Over-excitation
gain
030AH
0～2.000.64
P3-11
P3-12
P3-14
0V～rated motor voltage
0～100
-
0: Digital setting (P3-15)
1: AI1 2: AI2 3: AI3
4: Pulse setting (DI5) 5: Multi-reference
6: Simple PLC 7: PID
8: Communication setting
0V
Model
dependent
-
0
P3-15
030BH
030CH
030EH
030FH
V/F oscillation
suppression gain
Reserved
Voltage source
for V/F
separation
selection
Voltage digital
setting for
V/F separation
P3-13
--
030CH
Reserved
P4 Input Terminals function
0： No function 1： Forward RUN (FWD)
2： Reverse RUN (REV) 3： Three-Wire control
4： Forward JOG (FJOG) 5： Reverse JOG (RJOG)
6： Coast to stop 7： Emergency stop
8： Fault reset (RESET)
9： External fault input
10：Terminal UP
11：Terminal DOWN
12：UP and DOWN setting clear
13：Speed control/Torque control switchover
14：Speed search start enable
15：Reserved
16：Multi-reference terminal 1
17：Multi-reference terminal 2
18：Multi-reference terminal 3
19：Multi-reference terminal 4
20：Terminal 1 for acceleration/deceleration
time selection
21：Terminal 2 for acceleration/deceleration
time selection
22：Acceleration/Deceleration prohibited
23：PID control cancel
24：PID control pause
25：PID integral pause
26：PID characteristic switching
27：PID parameter switchover
28：PID target value switchover terminal1
29：PID target value switchover terminal2
30：PID target value switchover terminal3
31：PID feedback value switchover terminal1
32：PID feedback value switchover terminal2
33：PID feedback value switchover terminal3
34：PLC pause 35：PLC status reset
36：Swing enable 37：Swing pause
38：Swing reset
P4-00
Function
Code
S1 terminal
function
Parameter Name
Setting Range
1
Default
0400H
Address
P3-16
0V～rated motor voltage
0.0～1000.0s
0V
10.0s
P3-17
0310H
0311H
Voltage
acceleration
time of V/F
separation
Voltage
deceleration
time of V/F
separation
P3-18
--
0312H
Reserved
P4-01
S2 terminal
function
2
0401H
P4-02
S3 terminal
function
30402H
P4-03
S4 terminal
function
5
0403H
P4-04
S5 terminal
function
60404H
P4-05
S6 terminal
function
80405H