KVM KVM6000 Series - P6 Start;Stop Control Parameters

- 26 -
P5-31
P5-32
P5-33
P5-34
HDO output
selection
Analog output
signal selection
A01 output gain
A01 output offset
coefficient
051FH
0520H
0521H
0522H
15: PUL input value
16: Module temperature
17: Internal temperature
18: Excitation quantity
19: RS485 communication settings
BIT0: AO1 signal selection
0：0～10V
1：4.00～20.00mA
2：0.00～20.00mA
BIT1: AO2 signal selection
0: 0-10V
1: 4.00-20.00mA
2: 0.00-20.00mA
BIT2: HDO function enable
0: Ordinary switching value Y4 function
1: HDO high speed pulse output function
BIT3: Reserved
25.0200.0%
～
-10.010.0%～
2
0000
100.0%
0.0%
P5-35
P5-36
P5-37
0523H
0524H
0525H
100.0%
0.0%
0.20KHz
25.0200.0%～
-10.010.0%～
0.0050.00KHz～
A02 output gain
A02 output offset
coefficient
HDO pulse output
lower limit
P5-380526H
50.00KHz 0.0050.00KHz
～
HDO pulse output
upper limit
P6 Start/Stop Control parameters
Parameter Name
Setting Range
Start mode
BIT0：Start mode
0: Direct start
1: First braking and then start by startup
frequency
2: Rotational speed tracking
RESTART
0.0060.00Hz～
Minimum output
frequency
Function
Code
P6-00
P6-01
P6-02
0100%
～
Startup
pre-excited current
Startup
pre-excited time
Startup frequency
Startup frequency
holding time
Startup DC
braking current
Startup DC
braking time
0.0060.00s
～
0.0060.00Hz～
0.0050.00s～
0150%～
0.0300.0s～
P6-03
P6-04
P6-05
P6-06
P6-07
Address
0600H
0601H
0602H
0603H
0604H
0605H
0606H
0607H
Model
dependent
0.50Hz
Default
0
0.50Hz
30%
0.0s
0%
0.0s
- 27 -
KVM6000
Function Code Table KVM6000 Function Code Table
Stop DC
braking current
Waiting time of
stop DC braking
Stop DC braking
holding time
Acceleration mode
selection
Start of S-curve
acceleration time
End of S-curve
acceleration time
Start of S-curve
deceleration time
End of S-curve
deceleration time
Rotational speed
tracking mode
Zero speed
holding current
Initial frequency
of stop DC braking
0150%
～
0.0060.00s～
0.00600.0s～
BIT0：Acceleration/Deceleration time frequency
base
0：Base:50.00Hz1：Maximum frequency
BIT1：S-curve selection
0: Straight line 1: Curve
0.0120.00s
～
0: From frequency at stop 1: From zero speed
2: From maximum frequency
0150%～
0.0050.00Hz～
P6-09
P6-10
P6-11
P6-13
P6-14
P6-15
P6-16
P6-17
P6-18
P6-12
P6-08
0609H
060AH
060BH
060DH
060EH
060FH
0610H
0611H
0612H
060CH
0608H
0.00Hz
0%
0.0s
0.0s
0
0.50
0.50
0.50
0.50
0
0%
P6-19
Waiting time of
rotational speed
tracking
0.0600.0s
～
0613H
1.0s
P6-20
Tracking speed
of rotational
speed
0100
～0614H
20
P7 System configuration parameters
Function
Code
P7-00
Parameter Name
Parameter and key
lock selection
Address
0700H
Setting Range
BIT0:
0: Not locked
1: Function parameter locking
2: Function parameters and key locking (except
RUN/STOP/JOG)
3: Function parameters and keys are fully
locked
BIT1: Parameter group selection
0: Display all parameters
1: No display of Ax parameters
2: Only display P7 and PF parameters
Default
0
P7-01
User password
0701H
09999
～0000
P7-02
STOP key
function
0702H
BIT0:
0: Invalid for terminal command
1: Valid for terminal command
0000