Kyocera FS-1120MFP User Manual

iv
Compliance and Conformity
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• The use of a non-shielded interface cable with the referenced device is prohibited.
CAUTION
— The changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with Part 15 of FCC Rules.
Operation is subject to the following two conditions; (1) this device may not cause interference, and (2) this device must
accept any interference, including interference that may cause undesired operation of the device.
* The above warning is valid only in the United States of America.
Interface connectors
IMPORTANT Be sure to power off the machine before connecting or disconnecting an interface cable. For protection
against static electricity discharge to the machine's internal electronics through the interface connector(s), cover any
interface connector that is not in use with the protective cap supplied.
CDRH Regulations
The Center for Devices and Radiological Health (CDRH) of the U.S. Food and Drug Administration implemented
regulations for laser products on August 2, 1976. These regulations apply to laser products manufactured after August 1,
1976. Compliance is mandatory for products marketed in the United States. A label indicating compliance with the CDRH
regulations must be attached to laser products marketed in the United States.
Canadian Department of Communications Compliance Statement
This Class B digital apparatus complies with Canadian ICES-003.
Avis de conformité aux normes du ministère des Communications du Canada
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
Note Use shielded interface cables.

Kyocera FS-1120MFP Specifications

General

Duplex printing	Yes
Print technology	Laser
Maximum resolution	1800 x 600 DPI
Time to first page (black, normal)	8.5 s
Print speed (black, normal quality, A4/US Letter)	20 ppm
Copier resize	25 - 400 %
Maximum copy resolution	600 x 600 DPI
Maximum number of copies	99 copies
N-in-1 copy function (N=)	2, 4
Time to first copy (black, normal)	14 s
Copy speed (black, normal quality, A4)	20 cpm
Grayscale levels	256
Maximum scan area	Legal (216 x 356) mm
Scan speed (black)	18 ppm
Scan speed (color)	6 ppm
Image formats supported	BMP, JPG, PNG, TIF
Document formats supported	PDF
Faxing	Mono faxing
Fax memory	2.2 MB
Modem speed	33.6 Kbit/s
Fax coding methods	MH, MMR (Fax coding method), MR
Fax transmission speed	3 sec/page
Digital sender	No
Maximum duty cycle	- pages per month
Total input capacity	250 sheets
Total output capacity	150 sheets
Total number of input trays	1
Auto document feeder (ADF) input capacity	40 sheets
Maximum print size	216 x 356 mm
Paper tray media types	Envelopes, Plain paper
Paper tray media weight	60 - 220 g/m²
Non-ISO print media sizes	Folio
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5, B6
Maximum ISO A-series paper size	A4
Display	LCD
Product color	Black, White
Market positioning	Home & office
Display number of lines	2 lines
Standard interfaces	USB 2.0
Mobile printing technologies	Not supported
Internal memory	64 MB
Processor family	ARM
Sound power level (standby)	28 dB
Sound pressure level (copying)	50 dB
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	7 W
Power consumption (PowerSave)	3 W
Power consumption (average operating)	307 W
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Depth	361 mm
Width	390 mm
Height	362 mm