Kyocera FS-2020D Advanced Operation Guide

5-2 Maintenance
General Information
This chapter describes basic maintenance tasks you can perform for the
printer. You can replace the following component according to the
printer's display:
• Toner Kits
• Waste Toner Box
Also, the internal parts need periodic cleaning.
Toner Container Replacement
Frequency of toner container replacement
The life of the toner containers depends on the amount of toner required
to accomplish your printing jobs. According to ISO/IEC 19798 and
EcoPrint switched off the toner container can print as follows (A4/Letter
paper is assumed): 20,000 pages (FS-4020DN); 15,000 pages
(FS-3920DN); 12,000 pages (FS-2020D).
You can print a status page to check how much toner remains in the
toner container. The Toner Gauge in the consumables status section on
the status page shows a progress bar, which roughly represents how
much toner is left in the toner container.
Starter Toner Container
The toner container packed with the new printer is a starter toner
container. The starter toner container lasts an average of 10,000 pages
(FS-4020DN); 7,500 pages (FS-3920DN); 6,000 pages (FS-2020D).
Toner Kits
For best results, we recommend that you only use genuine Kyocera
Parts and Supplies. Should any damage be caused by the application of
a toner other than the original. Kyocera Mita toner, then this damage is
excluded from the guarantee.
A new toner kit contains the following items:
• Toner Container
• Plastic waste bag for old toner container and waste toner box
• Waste toner box
• Installation Guide
Note Information Collection on Memory Chips - The memory chip
attached to the toner container is designed to improve
convenience for the end user; to support the recycling operation of
empty toner containers; and to gather information to support new
product planning and development. The information gathered is
anonymous - it cannot be associated to any specific individual and
the data is intended to be used anonymously.
Note Do not remove the toner container from the carton until you
are ready to install it in the printer.

Kyocera FS-2020D Specifications

General

Color	No
Duplex printing	Yes
Print technology	Laser
Maximum resolution	1200 x 1200 DPI
Time to first page (black, normal)	9 s
Print speed (black, normal quality, A4/US Letter)	35 ppm
Memory type	DDR2
Processor model	PowerPC 440
Maximum internal memory	1152 MB
Sound power level (standby)	29 dB
Sound pressure level (printing)	52 dB
Power supply type	220/240 V, 50/60 Hz
Capacity cartridge	12000 sheets
Power consumption (active)	560 W
Recommended monthly print volume	20000 pages
Maximum duty cycle	150.000 pages per month
Number of print cartridges	1
Total input capacity	500 sheets
Total output capacity	250 sheets
Maximum input capacity	1100 sheets
Maximum number of input trays	2
Multi-Purpose tray input capacity	100 sheets
Maximum print size	216 x 356 mm
Paper tray media types	Plain paper, Recycled paper
Paper tray media weight	60 - 120 g/m²
Non-ISO print media sizes	Letter
ISO A-series sizes (A0...A9)	A4, A5, A6
ISO B-series sizes (B0...B9)	B5
Maximum ISO A-series paper size	A4
Multi-Purpose Tray media weight	60 - 220 g/m²
AC input voltage	220 - 240 V
AC input frequency	50 - 60 Hz
Power consumption (standby)	9.2 W
Power consumption (PowerSave)	5.7 W
Energy Star Typical Electricity Consumption (TEC)	2.6 kWh/week
Display	LCD
Certification	GS, TüV, CE
Standard interfaces	Parallel, USB 2.0
Optional connectivity	Ethernet, Wireless LAN
Sustainability certificates	ENERGY STAR

Weight and Dimensions

Dimensions (WxDxH)	382 x 394 x 285 mm