What causes the valve to not shut off on a lancer Sensation?
If the valve on your Lancer Beverage Dispenser will not shut off, it could be due to debris in the solenoid seat; activate the valve a few times to free the debris. Alternatively, the solenoid plunger might be sticking; remove the solenoid coil and plunger and clean out any foreign material.
Why does the BIB pump fail to stop when dispensing valve is closed in my lancer Sensation?
If the BIB pump on your Lancer Beverage Dispenser fails to stop when the dispensing valve is closed, it could be due to a leak in the discharge line or fittings, so repair or replace the discharge line. Alternatively, the BIB might be empty, so replace the BIB. Finally, there might be an air leak on the inlet line or bag connector, so repair or replace it.
Why does the BIB pump fail to restart after bag replacement in my lancer Sensation?
If the BIB pump on your Lancer Beverage Dispenser fails to restart after bag replacement, it could be due to a leak in the discharge line or fittings, so tighten the BIB connector. Alternatively, the BIB might be empty, so clean out or replace the BIB connector. Finally, there might be an air leak on the inlet line or bag connector, so straighten or replace the line.
What to do if lancer Sensation dispenses syrup only with CO2, but no water?
If your Lancer Beverage Dispenser is dispensing only syrup with CO2 but no water, several factors could be at play. First, check for proper water flow to the dispenser. If the carbonator pump motor has timed out, reset it by turning the unit off and then on using the circuit breaker on the power supply, or by momentarily unplugging the unit. Also, ensure the liquid level probe is correctly connected to the PCB. If the connections are good, the PCB assembly or the liquid level probe might be defective and require replacement. A weak or defective carbonator pump could also be the cause, necessitating its replacement.
Why is the BIB pump operating, but there is no flow in my lancer Sensation?
If the BIB pump on your Lancer Beverage Dispenser is operating, but there is no flow, it could be due to a leak in the syrup inlet or outlet line, so replace the line. Alternatively, the BIB pump itself might be defective and require replacement.
What to do if the push chute opens the ice door, but the motor doesn't run on my lancer Sensation?
If you press the push chute on your Lancer Beverage Dispenser, and the ice door opens but the motor does not run, there are a few potential causes. First, check if the wiring harness is plugged in and plug it in if necessary. A defective PC board could also be the problem, requiring replacement. Lastly, the motor itself might be defective, so consider replacing it.
Why does the BIB pump continue to operate when the bag is empty in my lancer Sensation Beverage Dispenser?
If your Lancer Beverage Dispenser has a BIB pump that continues to operate when the bag is empty, it could be due to a leak in the suction line, so replace the line. Alternatively, there could be a leaking o-ring on the pump inlet fitting, so replace the o-ring. Finally, the syrup BIB pump itself might be defective and require replacement.
What causes the BIB pump to not operate when dispensing valve is opened on my lancer Sensation Beverage Dispenser?
If your Lancer Beverage Dispenser has a BIB pump that does not operate when the dispensing valve is opened, there are several potential reasons. You might be out of CO2, the CO2 might not be turned on, or the CO2 pressure might be too low; replace the CO2 supply, turn on the CO2 supply, or adjust the CO2 pressure to 70-80 PSI (0.482 - 0.552 MPA). You might also be out of syrup, so replace the syrup supply. Ensure the BIB connector is tight. Finally, check for kinks in the syrup or gas lines and straighten or replace them.
Why is the water flow insufficient in my Lancer Beverage Dispenser (plain water drinks)?
If your Lancer Beverage Dispenser has insufficient water flow (plain water drinks), several factors could be the cause. First, verify that the incoming supply water pressure to the plain water inlet is a minimum of 75 PSI (0.517 MPA) and a maximum of 125 PSI (0.862 MPA). Ensure that the shutoff on the mounting block is fully open. Foreign debris in the water flow control can also cause this issue; remove the water flow control from the valve and clean out any foreign material. A water filtration problem could also be the cause, so service the water system as required. Finally, a defective LFCV module might be the problem, requiring replacement.
What to do if the push chute on my lancer Sensation Beverage Dispenser has no response?
If you press the push chute on your Lancer Beverage Dispenser and there is no response, several factors could be at play. First, ensure the dispenser is connected to a power source. If it is, check that the wiring harness is plugged in. A defective PC board could also be the issue, requiring replacement. Lastly, a malfunctioning power supply might be the cause; check the voltage to the power supply and inspect the fuses.
General| Category | Beverage Dispenser |
|---|---|
| Brand | Lancer |
| Series | Sensation |
| Material | Stainless Steel |
| Color | Silver |
To Next Page
