Need help?Do you have a question about the Lancom GS-1224 and is the answer not in the manual?
General| Form Factor | Rack-mountable |
|---|---|
| Switching Capacity | 48 Gbps |
| Forwarding Rate | 35.7 Mpps |
| MAC Address Table Size | 8K entries |
| Power Supply | Internal power supply |
| Layer | Layer 2 |
| Device Type | Switch |
| Ports | 24 x 10/100/1000 |
| Features | Quality of Service (QoS), VLAN support, Port Mirroring, IGMP snooping |
| Compliant Standards | IEEE 802.3, IEEE 802.3u, IEEE 802.3ab, IEEE 802.3x, IEEE 802.1p, IEEE 802.1q |
| Humidity | 10 - 90% (non-condensing) |
Details the manual's creation and available online and phone support from LANCOM.
Explains the meaning of warning, instruction, and information symbols used in the manual.
Highlights key features like QoS, Spanning Tree, VLAN, Port Trunking, and Bandwidth Control.
Details the hardware and management capabilities of the LANCOM GS-1224 switch.
Lists items included in the package and minimum system requirements for setup.
Explains LEDs, front panel connectors/buttons, and rear panel connectors for device status.
Provides steps for physically mounting the switch and connecting network devices and power.
Guides through installing Windows-compatible system software like LANconfig and LANmonitor.
Details how to access and use the WEBconfig interface for device configuration.
Explains the process of backing up and restoring the switch's configuration.
Describes how to use LANmonitor to monitor the switch's status and port activity.
Provides an overview of the switch's system information displayed after login via WEBconfig.
Details parameters for system description, firmware, MAC address, IP settings, and device name.
Explains how to configure individual switch ports, including Jumbo Frames and Power Saving.
Covers Tag-based, Port-based, and Metro VLAN modes, including group configuration.
Guides on configuring link aggregation to bundle multiple ports into a single logical port.
Explains Link Aggregation Control Protocol (LACP) for dynamic trunk group management.
Details Rapid Spanning Tree Protocol (RSTP) configuration for loop detection and network topology management.
Covers 802.1x configuration for user authentication and network access control.
Explains how to configure IGMP snooping to manage multicast traffic on specific ports.
Describes setting up port mirroring to monitor network traffic by copying packets to a designated port.
Details configuring QoS for prioritizing traffic based on VLAN tags (802.1p) and DSCP.
Guides on configuring IP filters to allow or deny access to switch management based on IP addresses.
Explains how to set ingress and egress bandwidth limits for each port.
Details configuring storm control to block unnecessary multicast and broadcast frames.
Covers SNMP configuration, community names, trap settings, and system event monitoring.
Explains how to monitor detailed port statistics, LACP, RSTP, IGMP, and Ping status.
Displays detailed traffic counts for each port, including received and transmitted packets, errors, and sizes.
Shows the status of Link Aggregation Control Protocol (LACP) for bundling ports.
Displays VLAN bridge information and the status of all ports related to Rapid Spanning Tree Protocol.
Shows IGMP status, including VLAN ID, querier, and group membership queries for multicast traffic.
Allows performing ping tests to check device availability and network connectivity.
Covers warm restart, factory default reset, software upgrades, and configuration file transfer.
Details the process of restarting the switch for configuration changes to take effect.
Explains how to restore the switch to its original factory default settings.
Guides on how to upload new firmware to upgrade the switch's software.
Describes backing up and uploading configuration files for disaster recovery or migration.
Explains methods for logging out of the web interface, including auto and manual logout.
Provides detailed technical specifications for switching technology, protocols, interfaces, and housing.
Details the pinout for the 8-pin RJ45 Ethernet interface (10/100/1000Base-TX).
States compliance with EC directives and where to find official declarations of conformity.
To Next Page
