Lanzar VBP251 - Vibe Pro Series Amplifiers and Woofer; VBP20 4200 Watts 2 Channel High Power Mosfet ampLIFIER; VBP11 1200 WATTS 4 Channel High Power mosfet Amplifier; VBPY21 2200 WATTS 4 Channel High Power mosfet amplifier

33
VBP281 4200 Watts 2 Channel High Power MOSFET Amplifier
Electronic Crossover Network •
Line Outs for L/R Channels •
Bass Boost Circuit•
Tri-Mode Capable •
Gold RCA Inputs •
Bridgeable at 4 Ohms •
2 Ohm Stereo Stable•
Advanced Protection Circuitry •
Stify Regulated PWM-Type Power Supplies •
Variable Input Level Controls for Each •
Pair of Channels
Frequency Response: 15Hz-35kHz •
Variable Low Pass Filter Control: 40Hz~350Hz•
Variable High pass Filter Control: 40Hz~3kHz•
Variable Bass Boost Control: 0dB-6dB-12dB (SW)•
High-Efciency, Heavy Aluminum Heatsink •
Power Protection LED Indicators •
Soft Turn On/Off•
2 x 1050 Watts RMS at 4 Ohms •
2 x 2100 Watts MAX at 4 Ohms •
2 x 1890 Watts RMS at 2 Ohms•
1 x 4200 Watts MAX at 4 Ohms MONO•
S/N Ratio: >95dB •
Fuse: 30A x 3•
9.33’’(W) x 2.56’’(H) x 21.66’’(L)•
VBP411 1200 Watts 4 Channel High Power MOSFET Amplifier
Electronic Crossover Network •
Line Outs for 3/4 Channels •
Bass Boost Circuit•
Tri-Mode Capable •
Gold RCA Inputs •
Bridgeable at 4 Ohms •
2 Ohm Stereo Stable•
Advanced Protection Circuitry •
Stify Regulated PWM-Type Power Supplies •
Variable Input Level Controls for Each •
Pair of Channels
Frequency Response: 15Hz-35kHz •
Variable Low Pass Filter Control: 40Hz~350Hz•
Variable High pass Filter Control: 40Hz~3kHz•
Variable Bass Boost Control: 0dB-6dB-12dB (SW)•
High-Efciency, Heavy Aluminum Heatsink •
Power Protection LED Indicators •
Soft Turn On/Off•
4 x 150 Watts RMS at 4 Ohms •
4 x 300 Watts MAX at 4 Ohms •
4 x 270 Watts RMS at 2 Ohms•
2 x 600 Watts MAX at 4 Ohms MONO•
S/N Ratio: >95dB •
Fuse: 25A x 2•
9.33’’(W) x 2.56’’(H) x 13’’(L)•
VBP421 2200 Watts 4 Channel High Power MOSFET Amplifier
Electronic Crossover Network •
Line Outs for 3/4 Channels •
Bass Boost Circuit•
Tri-Mode Capable •
Gold RCA Inputs •
Bridgeable at 4 Ohms •
2 Ohm Stereo Stable•
Advanced Protection Circuitry •
Stify Regulated PWM-Type Power Supplies •
Variable Input Level Controls for Each •
Pair of Channels
Frequency Response: 15Hz-35kHz •
Variable Low Pass Filter Control: 40Hz~350Hz•
Variable High pass Filter Control: 40Hz~3kHz•
Variable Bass Boost Control: 0dB-6dB-12dB (SW)•
High-Efciency, Heavy Aluminum Heatsink •
Power Protection LED Indicators •
Soft Turn On/Off•
S/N Ratio: >95dB •
Fuse: 30A x 2•
9.33’’(W) x 2.56’’(H) x 14.57’’(L)•
4 x 275 Watts RMS at 4 Ohms •
4 x 550 Watts MAX at 4 Ohms •
4 x 495 Watts RMS at 2 Ohms•
2 x 1100 Watts MAX at 4 Ohms MONO•
VBP1801D 1800 Watts Mono Block MOSFET Digital Power Amplifier
Electronic Crossover Network •
Line Outs for L/R Channels •
Bass Boost Circuit•
Tri-Mode Capable •
Gold RCA Inputs •
1 Ohm Stable•
Advanced Protection Circuitry •
Stify Regulated PWM-Type Power Supplies •
Double Sided Epoxy PCB Circuit Board•
Custom Terminal Block for Speaker Connections•
Variable Input Level Controls for Each •
Pair of Channels
1 x 400 Watts RMS at 4 Ohms •
1 x 800 Watts RMS at 2 Ohms •
1 x 1000 Watts RMS at 1.3 Ohms•
1 x 1800 Watts MAX at 1.3 Ohms•
Remote Subwoofer Bass Control •
Frequency Response: 15Hz~400Hz •
Variable Low Pass Filter Control: 40Hz~350Hz•
Variable Subsonic Filter Control: Off-25Hz (SW)•
Variable Bass Boost Control: 0dB~18dB •
High-Efciency, Heavy Aluminum Heatsink •
Power Protection LED Indicators •
Soft Turn On/Off•
S/N Ratio: >100dB •
Fuse: 30A x 4•
9.33’’(W) x 2.56’’(H) x 16.94’’(L)•
VBPW1236D 12’’ 2000 Watts Die-Cast Aluminum Dual Channel Subwoofer
Custom Tooled Die-Cast Aluminum Basket •
Non Pressed Paper Cone •
Massive Butyl Rubber Surround •
3’’ High Temperature Dual Voice Coil •
95 Oz x 3 High Density Barium Ferrite Magnet •
Power Handling: 2000 Watts Peak •
Frequency Response: 26- 800 Hz •
Impedence: Dual 4 Ohms•
Efciency: 88dB •
Includes Installation Hardware and Template•
vibe pro series amplifiers and woofer
Lanzarcopy.indd 33 11/24/2009 7:11:03 PM