VB26 Vibe 280 Watts 6.5’’ 2 Way Coaxial Speakers
Standard 6.5’’ Size Fits OEM Locations •
High Quality Injection Cone •
Non-Fatiguing Butyl Rubber Surround •
1’’ High Temperature Kapton Voice Coil •
1’’ Silk Dome Neo-Tweeter •
Texture Coat Finish on Steel Basket•
25 Oz Magnet Structure •
Rubber Magnet Boot•
Power Handling: 250Watts RMS / 500Watts Peak •
Frequency Response: 55-20KHz •
Impedance: 4 Ohms •
Mounting Depth: 2.66’’ •
Includes Custom Molded Grills, Wires and •
Installation Hardware
VB369 Max 380 Watts 6’’ X 9’’ 3 Way Coaxials Speaker
Standard 6’’X9’’ Size Fits OEM Locations •
High Quality Injection Cone •
Non-Fatiguing Butyl Rubber Surround •
1’’ Silk Dome Neo-Midrange •
18 mm Silk Dome Neo-Tweeters •
1.25’’ High Temperature Kapton Voice Coil •
Texture Coat Finish On Steel Basket •
40 Oz Magnet Structure •
Rubber Magnet Boot•
Power Handling: 400Watts RMS / 800 Watts Peak •
Frequency Response: 40-22kHz •
Impedance: 4 Ohms •
Mounting Depth: 3.35’’ •
Includes Custom Molded Grills, Wires and •
Installation Hardware
MTP5X7 5’’ x 7’’/6’’ x 8’’ Two-Way Plate Speaker System
Standard 5’’x 7/6’’x8’’ Size Fits OEM Cut-Outs •
Special Mica-Poly Composite Cone •
Non-Fatiguing Butyl Rubber Surround •
High Temperature Voice Coil •
High Density Barium Ferrite Magnet •
.5’’ Mylar Dome Neodymium Tweeter •
Swivel Tweeter Positioning •
Built-In Crossover Capacitor •
Rubber Boot Magnet Cover •
Power Handling: 85 Watts RMS/170 Watts Peak •
(Full-Range) 100 Watts RMS/200 Watts Peak
(Crossed-Over Mode)
Frequency Response: 55Hz - 23kHz (Full-Range •
Mode) 200Hz - 23kHz (Crossed-Over Mode)
4 Ohms Impedance •
Mounting Depth: 2.1’’ •
Wiring Diagram and Installation Template Included•
TCS 1’’ Silk Dome Neodymium Flush, Surface or Angle Mount Tweeter
1’’ Silk Dome Tweeter •
High Density Neodymium Magnet •
Tri-Way Mounting System: Flush, Surface or •
Angle Mount
Ferro Fluid Cooling •
Frequency Response: 1.4-24k Hz •
SPL: 94 dB @ 1W/1M •
Power Handling: 200 Watts•
TWS 1’’ Titanium Dome Neodymium Flush, Surface or Angle Mount Tweeter
1’’ Titanium Dome Tweeter •
High Density Neodymium Magnet •
Tri-Way Mounting System: Flush, Surface or •
Angle Mount
Ferro Fluid Cooling •
12 dB Crossover Network •
Frequency Response: 2-25kHz •
SPL: 96 dB @ 1W/1M •
Power Handling: 200 Watts•
DCT 1’’ Silk Dome Neodymium Flush, Surface or Angle Mount Tweeter
1’’ Silk Dome Tweeter •
High Density Neodymium Magnet •
Tri-Way Swivel Mounting System: Flush, Surface or •
Angle Mount
Ferro Fluid Cooling •
Frequency Response: 1.3-24k Hz •
SPL: 96 dB @ 1W/1M •
Power Handling: 150 Watts•
vibe series coaxial speakers and tweeters
To Next Page
