Leach 2R-III - User Manual

Questions and Answers

A
Anne RiceAug 20, 2025
What to do if Leach 2R-III packer/carrier panels lack full force?
- M
  Michael DonovanAug 20, 2025
  If the packer/carrier panels on your Leach Garbage Disposal aren't delivering full force, consider these potential issues: * Incorrect hydraulic pressure: Perform a pressure check. * Low hydraulic fluid level: Add fluid to the correct level. * Dirty tank strainer screen: Service the system. * Wrong type of hydraulic fluid: Drain and refill with the correct type. * Main relief section of the Front Control Valve opens too soon: Adjust the main relief setting on the Front Control Valve.
Q
qjacksonAug 22, 2025
Why won't the engine speed up on my Leach Garbage Disposal?
- G
  Gary CombsAug 22, 2025
  If the engine of your Leach Garbage Disposal isn't speeding up when the carrier panel lever or speed-up button is engaged, the following could be the reasons: * A short in the electrical wiring: Repair the broken wire. * A blown fuse on the speed-up relay: Replace the fuse and check the electrical system for shorts. * A defective relay or switch: Check for and replace any defective parts. * The electrical system is not grounded properly: Check all ground connections for corrosion or breaks, then clean or repair them. * The carrier panel lever speed-up switch or linkage is defective: Repair, replace, or adjust as required.
T
Teresa CunninghamAug 25, 2025
What to do if the load won't push out of my Leach 2R-III Garbage Disposal?
- T
  Tammy HartAug 26, 2025
  If the load won't push out of your Leach Garbage Disposal, here are a couple of potential causes: * Less than full pressure in the telescopic cylinder: Perform a test for a leaking cylinder and repair it. Adjust the main relief pressure. * Trying to push the load out against an obstruction: Move the unit forward to finish unloading.
J
Julia VincentAug 27, 2025
Why won't the engine speed return to normal on my Leach 2R-III?
- K
  Kyle MarquezAug 28, 2025
  If the engine speed on your Leach Garbage Disposal doesn't return to normal after the packing cycle is complete or when the speed-up button is released, it could be due to: * A short circuit in the electrical system: Check for and repair any shorts in the system. * A defective carrier panel lever speed-up switch: Repair, replace, or adjust as required.
H
Heather RomanAug 30, 2025
Why won't the tailgate raise on my Leach Garbage Disposal?
- J
  jenniferjonesAug 30, 2025
  If the tailgate of your Leach Garbage Disposal won't raise, consider the following potential causes: * Tailgate clamps still engaged: Disconnect clamps and swing free of tailgate. * Insufficient hydraulic pressure: Check main relief pressure. * Defective hydraulic pump: Replace pump. * Main relief cartridge out of adjustment or broken: Adjust or replace the main relief cartridge as necessary. * Tailgate lift cylinders leaking or defective: Repair or replace as required. * Restriction in tailgate cylinder hose: Remove and clean hose.
J
Joanne WilliamsSep 1, 2025
How to fix a slow cycle time on Leach 2R-III?
- B
  Barbara RaySep 1, 2025
  A slow cycle time on your Leach Garbage Disposal could be caused by: * Engine RPM too low: Set the engine RPM to achieve a 23 to 26-second cycle time (must be done by an authorized dealer). * Hydraulic fluid level too low: Fill to the proper level. * Hydraulic fluid filter needs servicing: Service the filter. * Hydraulic tank breather dirty: Service the breather.
B
Beth PowellSep 4, 2025
What to do if the container won’t lift on my Leach Garbage Disposal?
- D
  Debra MillerSep 4, 2025
  If a container won't lift with your Leach Garbage Disposal, check these potential issues: * Insufficient hydraulic pressure: Check pressures. * Broken cable: Replace the cable. * Cable loose from the lifting device (drum/cylinder): Secure the cable to the lifting device. * Container overload: Reduce the weight of the material in the container. * Container frozen to the ground: Do not use the lifting device to break the container loose from the ground.
S
Steven MacdonaldSep 6, 2025
What to do if the pushout panel won't slide forward automatically on my Leach 2R-III Garbage Disposal?
- L
  Lance ThompsonSep 6, 2025
  If the pushout panel on your Leach Garbage Disposal isn't sliding forward automatically, consider the following: * Resistance setting too high: Reduce the resistance setting. * Packer/carrier panels not applying full force: Check pressures and the pump.
J
John CooperSep 9, 2025
What to do if the packer panel valve section will not shift on Leach 2R-III?
- T
  Tina ConnerSep 9, 2025
  If the packer panel valve section on your Leach Garbage Disposal will not shift, it could be due to: * A leaking packer panel cylinder: Perform a test for a leaking cylinder. * Packer panel valve section shift pressure too high: Perform a pressure check. * Linkage binding or restrictive: Inspect and free the linkage as necessary.
J
Julia ClarkSep 12, 2025
What to do if the carrier panel valve section will not shift to neutral on Leach 2R-III Garbage Disposal?
- S
  Samantha JohnsonSep 12, 2025
  If the carrier panel valve section on your Leach Garbage Disposal will not shift to neutral, here are some possible causes: * Carrier panel cylinder leaking: Perform test for leaking cylinder. * Carrier panel valve section shift pressure too high: Perform a pressure check. * Linkage binding or restrictive: Inspect and free linkage as necessary.