Lenze 2102 - Page 43

Appendix
8-11
L _^ONMObk
Code Name
Keypad PC
1)
Error Cause
Remedy
C0161
*
C
*
Fault
---
0 No error - -
C0162
*
C
0
1
6
3
*
memory
ccr
71 System error
Strong interference on control cables Shield control cables
C0163
*
C
0
1
6
4
*
(
P
8
2
X
X
)
c
c
r
7
1
S
y
s
t
e
m
e
r
r
o
r
Ground or earth loops in the wiring
C
0
1
6
4
*
(P82XX)
ce0
61 Communication error to
AIF
Faulty transmission of control commands
via AIF
Insert the communication module into the hand
terminal
ce1
62 Communication error to
CAN-IN1 with sync
control
CAN-IN1-object receives faulty data or
communication is interrupted
Plug-in connection - bus module ó Check FIF
Check transmitter
Increase monitoring time under C0357/1 if
necessary
ce2
63 Communication error to
CAN-IN2
CAN-IN2-object receives faulty data or
communication is interrupted
Plug-in connection - bus module ó Check FIF
Check transmitter
Increase monitoring time under C0357/2 if
necessary
ce3
64 Communication error to
CAN-IN1 with event or
time control
CAN-IN1-object receives faulty data or
communication is interrupted
Plug-in connection - bus module ó Check FIF
Check transmitter
Increase monitoring time under C0357/3 if
necessary
ce4
65 BUS-OFF
(many communication
errors occurred)
Controller has received too many incorrect
telegrams via the system bus and has
been disconnected
Check whether bus terminator available
Shield control of the cables
Check PE connection
Check bus load, if necessary, reduce the baud
rate
ce5
66 CAN Time-Out
For remote parameter setting via system
bus (C0370):
Slave does not answer. Communication
monitoring time exceeded.
Check system bus wiring
Check system bus configuration
For operation with module in FIF:
Internal fault
Contact Lenze
EEr
91 External fault (TRIP-Set) A digital signal assigned to TRIP set has
been activated
Check external encoder
H05
105 Internal fault Contact Lenze
id1
140 Faulty parameter
identification
Motor not connected Connect motor
LP1
32 Fault in motor phase
(TRIP)
Failure of one/several motor phase(s)
Check motor cables,check V
min
boost, connect
the motor with the corresponding power or
182 Fault in motor phase
(warning)
Motor current too low
t
h
e
m
o
t
o
r
w
i
t
h
t
h
e
c
o
r
r
e
s
p
o
n
d
i
n
g
p
o
w
e
r
o
r
adapt it under C0599.
LU
103
0
DC-bus undervoltage
(
o
n
l
y
m
e
s
s
a
g
e
w
i
t
h
o
u
t
Mains voltage too low Check mains voltage
0
(
on
l
y message w
i
t
h
out
TRIP)
DC-bus voltage too low Check supply cable
OC
1
11 short-circuit
short-circuit Find reason for short-circuit; check motor cable
O
C
1
1
1
s
h
o
r
t
c
i
r
c
u
i
t
Excessive capacitive charging current of
the motor cable
Use shorter motor cables with lower charging
current
OC
2
12 Earth fault
Grounded motor phase Check motor, check motor cable
O
C
2
1
2
E
a
r
t
h
f
a
u
l
t
Excessive capacitive charging current of
the motor cable
Use shorter motor cables with lower charging
current
OC3
13 Overload inverter during
acceleration or short
Acceleration time too short (C0012) • Increase acceleration time
• Check drive dimensioning
a
c
c
e
l
e
r
a
t
i
o
n
o
r
s
h
o
r
t
circuit
Defective motor cable Check wiring
Interturn fault in the motor Check motor
OC4
14 Overload controller during
deceleration
Deceleration t ime set too short (C0013) • Increase deceleration time
• Check size of external brake resistor
OC5
15 Controller overload in
stationary operation
Frequent and long overload Check drive dimensioning
OC6
16 Motor overload (I
2
xt
overload)
Motor is thermally overloaded, for
instance, because of
o
v
e
r
l
o
a
d
)
• impermissible continuous current • Check drive dimensioning
• frequent or too long acceleration
processes
• Check setting of C0120
Buy: www.ValinOnline.com | Phone 844-385-3099 | Email: CustomerService@valin.com
Show/Hide Bookmarks