LG WFT15D81E(H)P User Manual

48
10) Spin extraction is not proceeded.
Where, what & how to check?
Result of Check
Possible Cause
How to repair & settle
Motor
2) If there is no motor-working sound;
Check frequency of the Ball Pressure
Sensor (Pressure Switch), under no
load, or
Check contact defect of the safety
switch, defect of connection parts and
whether the lid is open if door error is
displayed.
Is placed the magnetic in Lid.
Check resistance of the motor.
Drain Motor/Clutch
1. In the case the motor rotates but the
inner tub does not rotates;
1) Check resistance of the drain motor if
the drain motor doesn’t work,or
2) Check gap between the PV link and the
brake lever if the inner tub does not
rotates while the drain motor works.
Less than 26.3 kHz
The lid is open
Defect of connection
part.
The lid is open.
Defect of magnetic in
LID
Contact defect of the
Ball Pressure Sensor
(Safety Switch)
∞Ω
∞Ω
Resistance is normal
The clearance is less
than 2.0mm or more
then 3.5mm
The gap is normal
(2.0~3.5mm)
Defect of the Ball
Pressure Sensor
(Pressure Switch).
Mistake in use.
Mistake in use.
Coil is open.
Coil is open.
Defect of connection part
or defect of the controller.
Assembling defect of the
drain motor or the clutch
Defect of the clutch.
Change the Ball Pressure
Sensor (Pressure Switch).
Explain “The lid is close
during operation”
Reconnect the conncetors.
Explain “The lid is close
during operation”
Change the Lid
Change the Ball Pressure
Sensor (Safety Switch).
Change the motor.
Change the drain motor.
Change the controller after
checking connection parts.
Reassemble the drain
motor or the clutch to
keep the clearance.
Change the clutch.
11) Spining is going on even though the lid is open.
Where, what & how to check?
Result of Check
Possible Cause
How to repair & settle
Safety Switch
1. Check resistance between both
terminals of the safety switch with the lid
open.
Ball Pressure Sensor
1. Is placed the magnetic on the wash?
0 ~ 9 Ω
∞Ω
Yes
No
Contact points of the
safety switch are welded.
Defect of the controller.
Reed S/W is short by
magnetic on the washer.
Reed Switch.
Change the Safety Switch
Change the controller
Keep magnet away from the
washer.
Change the controller.

LG WFT15D81E(H)P Specifications

General

POWER SOURSE	Refer to rating label on the back of Washer
AUTO POWER OFF	Applied
INPUT	Refer to rating label on the back of Washer
CAPA CITY	Refer to rating label on the back of Washer
SPIN SPEED	220 ~240 V / 50Hz : 680 50 110~127 V / 60Hz : 680 50 220 V / 60Hz : 730 50
INNER TUB	Stainless
LINT FILTER	Single
SOFTENER DISPENSER	Applied
DETERGENT DISPENSER	Applied
BLEACH INILET	Applied
ADDITIVES DISPENSER	Applied
INLET WATER PRESSURE	0.3kgf/cm2 ~ 8kgf/cm2
WATER LEVEL	9 Stages
PROGRAM	Fuzzy, Hand Wash, Heavy, Delicate, Wool, Eco Save, Wash Only, Quick Wash, Rinse / Spin, Spin Only
RESERVATION	Available for 3~ 48 Hr
UNBALANCE SWITCH	B.P Sensor
LID INTERLOCK SWITCH	Magnet Sensor
CHILD LOCK	Applied

Weight and Dimensions

DIM.	Refer to rating lavel on the back of Washer
WEIGHT	Refer to rating lavel on the back of Washer