Loewe Individual 55 Compose 3D, Individual 46 Compose 3D, Individual 40 Compose 3D, Individual 32 Compose 3D User Manual

133 -
english
Operating Loewe equipment
Using the remote control for the TV mode of the TV set
Press the TV button, the display above it will light for
approx. 5 seconds.
Using the remote control for a Loewe recorder
Press the REC button, the display above it will light for
approx. 5 seconds.
Using the remote control for a Loewe player
Press the DVD button, the display above it will light for
approx. 5 seconds.
Using the remote control for the radio mode of the TV set
Press the AUDIO button, the display above it will light for
approx. 5 seconds.
As long as a button is pressed, the display of the selected operating mode
lights up (TV – REC – DVD – AUDIO). This allows you to check which op-
erating mode the remote control is set to every time you press a button.
The factory setting of the buttons is described above (see also table in
right hand column). The assignment of the buttons can be changed to
suit the existing accessory devices (see right hand column).
Set unit for sound control function on the remote control
The buttons for the sound control functions Volume (
10
), Sound on/off (
1
) and Sound mode/Sound adjustment (
30
) have been programmed to
interact with the TV at the factory. The unit to be operated can be modified.
Press the TV button and the numeral button at the same
time for minimum 5 seconds. The LED above the TV
button flashes twice.
Funtion Buttons Unit
Audio-
functions
TV + 3 Auro/AudioVision/MediaVision 3D
TV + 4 Mediacenter
TV + 5 Loewe TV
TV + 6 Loewe TV with sound projector without
system connection
Setting the remote control for other Loewe devices
You can operate various Loewe devices with the remote control. The
device keys REC – DVD – AUDIO can be reassigned to operate various
Loewe devices.
Press the required device buttons and the Stop button
simultaneously for 5 sec. until the corresponding LED
display flashes twice.
Then enter the two-digit device code from the list below.
The associated LED display flashes twice.
Device Code Factory setting
Loewe ViewVision 8106 H 10
Loewe Viewvision, Centros 21x2 12
Loewe ViewVision DR
+
DVB-T 13 REC
Loewe Auro 2216 PS/8116 DT 14
Loewe BluTech Vision 15
Loewe Soundprojector 17
Loewe TV - Digital radio 19 AUDIO
Loewe Mediacenter 20
Loewe BluTech Vision Interactive 21 DVD
HDMI CEC mode 22
Loewe AudioVision 24
Loewe Individual Sound Projector SL 25
Apple IR codes 26
Apple IR codes (Apple TV-2G) 27
Loewe Soundbox 28
Loewe SoundVision 29
Loewe Air Speaker 30
Loewe MediaVision 3D 35
Resetting to factory setting 99
➠ The codes shown here only apply for direct operation of the acces-
sory device.
➠ For operation of the connected accessory device via the TV set, e.g.
with concealed installation (Code 22), see page 121. The remote
control’s signal is transmitted from the TV set to the accessory device
with concealed installation.
➠ The codes that are available may vary depending on the status of the
firmware that the remote control has.
External devices

Loewe Individual 55 Compose 3D, Individual 46 Compose 3D, Individual 40 Compose 3D, Individual 32 Compose 3D Specifications

General

Brand	Loewe
Model	Individual 55 Compose 3D, Individual 46 Compose 3D, Individual 40 Compose 3D, Individual 32 Compose 3D
Category	TV
Language	English