To Next PageTo Next PageWhy do my Logenex A202CR Intercom System phones ring as soon as the wires are plugged into the door station?
Your phones may be ringing immediately after plugging in the wires to the door station because the red and green wire to the door station is either reversed, has a short, or has a break in connection. You can verify this by plugging the door station into another available speaker relay port.
General| Brand | Logenex |
|---|---|
| Model | A202CR |
| Category | Intercom System |
| Language | English |
Verification of telephone system voltage compliance for safe operation.
Essential safety guidelines for using the telephone system equipment.
Explains how to identify X Series kit and doorstation model numbers.
Detailed technical specifications for the Logenex X Series controller.
Detailed technical specifications for the Logenex X Series doorstation.
Detailed technical specifications for the Logenex X Series camera.
Explains how to identify S Series kit and doorstation model numbers.
Detailed technical specifications for the Logenex S Series controller.
Detailed technical specifications for the Logenex S Series doorstation.
Detailed technical specifications for the Logenex S Series camera.
Canadian Department of Communications certification details.
Overview of TeleDoorBell system features and user capabilities.
List of components included in the TeleDoorBell "X Series" system package.
Connection point for the unit's AC power supply.
Indicator light for unit power status and operation.
Connections for incoming telephone line and outgoing connections.
Ports for door stations and dry contact relays.
Guidance on necessary components and wiring for installation.
Recommendation to use surge protectors for power and C/O lines.
Step-by-step guide for installing the X Series Audio & Video door station.
Note on adjusting volume control for different acoustic environments.
Step-by-step guide for installing the S Series Audio & Video door station.
Specific note for video setup on S Series models.
Note on adjusting volume control for different acoustic environments.
Instructions for rewiring the doorbell and transformer connections.
Specifications for normally open relays.
Reference to pages for door station connectivity.
Diagram showing TBG-1 connections with the A202CR & A204CR.
Diagram for installing the LX-DSL3F 3-Port Filter.
Warning about potential low-level audio cross-talk with the DSL filter.
Diagrams for connection using existing lines or C/O port.
Notes on TeleDoorBell function and monitoring with KSU/PBX systems.
Instruction to program phone system for extensions.
Verification of telephone system voltage compliance for safe operation.
How to use paging features with the amplifier and speaker system.
Instructions for turning muting on or off for Hi-Fi units.
Explanation of Hi-Fi specific features like muting during calls.
How to change ringing patterns for door stations.
How to program phone numbers for call restriction.
How to enable/disable Caller ID display for door stations.
How to configure multiple relays to trigger on door button press.
How to program Relay #3 for doorbell chime activation.
How to enable remote dial-up answering for programming functions.
How to set the phone number for door station call forwarding.
How to set the timing for relay activation (0.5 to 49 seconds).
How to adjust the call forwarding hang-up time.
How to change the system's 4-digit passcode.
How to restore all programming and settings to factory defaults.
Details on Hi-Fi specific features like muting and ring-over-page.
How to use paging features with the Hi-Fi system.
Instructions for controlling muting on Hi-Fi Series Units.
Solutions for when the controller fails to power up or has LED issues.
Troubleshooting communication issues between door station and phones.
Solutions for phones ringing but no communication, or vice versa.
Solutions for dial tone feedback when pressing door speaker button.
Troubleshooting invalid number recording during monitoring.
Solutions for low communication volume with the door station.
Troubleshooting phones ringing immediately upon wiring.
Solutions for indistinguishable ring patterns or system not recognizing patterns.
Troubleshooting specific door stations not ringing.
Solutions for inability to make long distance calls.
Troubleshooting call forwarding issues.
Troubleshooting video feed issues, modulation, or picture quality.
Details of the one-year limited warranty for the product.
Information on warranty for international customers.
Steps to follow for obtaining warranty service.
Factors that can void the product's warranty.
Statement disclaiming other express or implied warranties.
Procedure for out-of-warranty repair services.
Requirements for notifying the telephone company about connections.
Standards for connecting to the telephone network.
How telephone company changes affect equipment compatibility.
Notice regarding attachment limitations and electrical grounding.
Explanation of Load Number (LN) for telephone loop connection.
