Marantz AV8802/U1B - Page 78

1.10. About the error code
SeethetablebelowforerrorcodesanddetailsoffaultswhenthermwareisupdatedthroughUSBmemory.
Error
Code
USB Update Error Display Details of Error code Coping strategies
01
C o n n e c t i o n f a i l
0 1
Unable to detect USB.
Disconnect and connect the USB
memory.
02
F i l e s N o t F o u n d
0 2
No Firmware File in USB.
Make sure that the Firmware File is in
the USB memory.
03
N o t M a t c h F i r m
0 3
Firmware File in USB for unsup-
ported Model name/area.
Check the supported Model name/area
for the Firmware File.
04
C o n n e c t i o n f a i l
0 4
Failed to obtain entire Firmware
information.
Start the USB Update again.
05
C o n n e c t i o n f a i l
0 5
Time Out while obtaining entire
Firmware information.
Start the USB Update again.
08
C o n n e c t i o n f a i l
0 8
Error notication received while
requesting Firmware Info.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
09
C o n n e c t i o n f a i l
0 9
Time Out while obtaining Firm-
ware information.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
0A
C o n n e c t i o n f a i l
0 A
Unable to detect USB for Firm-
ware Download.
Disconnect and connect the USB
memory.
0B
F i l e s N o t F o u n d
0 B
No Firmware File for Firmware
Download.
Disconnect and connect the USB
memory.
0D
C o n n e c t i o n f a i l
0 D
Received value with invalid Pack-
age Version.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
10
M a i n * * * m i n
U p d a t i n g f a i l 1 0
No Update Packet received from
CX870 / CY920 (Time Out).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
11
M a i n * * * m i n
U p d a t i n g f a i l 1 1
Abnormal data in Update Packet
received from CX870 / CY920
(CRCError).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
12
M a i n * * * m i n
U p d a t i n g f a i l 1 2
Abnormal data in Update Packet
received from CX870 / CY920
(PacketNoError).
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
13
M a i n * * * m i n
E r a s e f a i l 1 3
Block Erase failed before rewriting
Main.
This unit automatically retries several
times. Wait until the FL display stops.
If the FL display stops at the Error dis-
play, press and hold the "Power opera-
tion" button for ve seconds.
78