Marantz PM-15S1 - Before Use; Equipment Mains Working Setting; Copyright Information; Placement Precautions

4
ID No.: 0 INPUT SELECTOR: CD VOLUME: -
SIDE ILLUMINATION: ON DISPLAY: ON ATT: OFF
LEVEL TRIM: 0.0 (L/R) TONE: OFF SPEAKER : OFF
ATT: -20dB REC OUT: OFF PHONO MC:OFF
ᘙųᅆ ϋųܾ
1
ERROR 02 ID
ဪӭ
2
ƷǢȳȗ
ƕ᣻ᙐƠƯƍLJƢŵ
2
ERROR 03 ID
ဪӭ
3
ƷǢȳȗ
ƕ᣻ᙐƠƯƍLJƢŵ
3
ERROR 04 ID
ဪӭ
4
ƷǢȳȗ
ƕ᣻ᙐƠƯƍLJƢŵ
4
ERROR 11 ID
ဪӭ
2
᳸
4
ƷǢ
ȳȗƕ
ID
ဪӭ
1
Ʒ
ǢȳȗƱᡫưƖLJ
Ƥǜŵ
5
ERROR 12 ID
ဪӭ
1
ƷǢȳȗ
ƕ
ID
ဪӭ
2
᳸
4
Ʒ
ǢȳȗƱᡫưƖLJ
Ƥǜŵ
ݣųሊ
ID
ဪӭƕ᣻ᙐƠƳƍǑƏƴ
ID
ဪӭǛᚨܭƠƯƘƩƞƍŵ
•ID
ဪӭ
1
ƷǢȳȗƴᩓเƕ
λƬƯƍƳƍئӳƸᩓเǛ
λǕƯƘƩƞƍŵ
•
ȪȢȸȈDZȸȖȫƕദƠƘ
ዓƞǕƯƍǔƔᄩᛐƠƯ
ƘƩƞƍŵ
•ID
ဪӭ
1
ƷǢȳȗƕ᣻ᙐƠ
ƯƍǔئӳƸ
ID
ဪӭǛദ
ƠƘᚨܭƠƯƘƩƞƍŵ
•
ȪȢȸȈDZȸȖȫƕദƠƘ
ዓƞǕƯƍǔƔᄩᛐƠƯ
ƘƩƞƍŵ
ERROR MESSAGES
Error Contents
1
ERROR 02 The units of ID No.2
overlaps.
2 ERROR 03 The unit of ID No.3
over laps.
3
ERROR 04 The unit of ID No.4
overlaps.
4
ERROR 11 The unit of ID No.2
to No.4 cannot com-
mu ni cate with the
unit of ID No.1.
5 ERROR 12 The unit of ID No.1
cannot com mu -
ni cate with the unit
of ID No.2 to No.4
Measure
ID number is changed
into the ID No. not over-
lap ping.
•
If the unit ID number 1 is
not turn on, turn on the
unit ID No.1.
•
Check the remote cable
is connected correctly.
•
ID No. is changed into ID
No. not overlapping.
•
Check the remote cable
is connected correctly.
ǨȩȸȡȃǻȸǸ
ǨȩȸȡȃǻȸǸ
2. Press DISPLAY button, the display will be the following.
3. Press DISPLAY button, the display will be the following.
4. Turn off power to quit service mode.
Service mode can be ended if turn off power from every
procedure.
The memory is cleared and the unit is initialized.
Initial settings
Be sure to set up manually.
MODE SW on Rear panel: STEREO
POWER ON/OFF SW: OFF
2.

DISPLAY
ȜǿȳǛƠLJƢŵɦᚡƷᘙᅆƴƳǓLJƢŵ
3.

DISPLAY
ȜǿȳǛƠLJƢŵɦᚡƷᘙᅆƴƳǓLJƢŵ
4.

POWER ON/OFF
ȜǿȳǛƠŴᩓเǛЏǓLJƢŵǵȸ
ȓǹȢȸȉƕᚐᨊƞǕLJƢŵ
ǵȸȓǹȢȸȉƸƲƷ৖᪯ƔǒNjᩓเǛЏǔƱኳʕƢǔƜ
ƱƕưƖLJƢŵ
ஜ˳ƷᚨܭƸμƯɦᚡƷЈᒵཞƴƳǓLJƢŵ
Јᒵཞϋܾ
ɦᚡƸŴ৖ѣưᚨܭ
/1&'59Ჴ56'4'1Ტ࣏ƣᚨܭᲣ
219'4101((59Ჴ1((