Marantz PM-11S2 - User Manual

Other manuals for Marantz PM-11S2

Service Manual91 pages

Questions and Answers

K
Kim HuffmanJul 28, 2025
What to do if my Marantz PM-11S2 Amplifier has power but no sound?
- J
  jcomptonJul 28, 2025
  If your Marantz Amplifier has power but you're not hearing any sound from the speakers, there are several things to check: * Ensure the speaker cables and input cables are properly connected. * Verify the connected player is operating correctly by referring to its instruction manual. * Make sure the INPUT SELECTOR knob is correctly set. * Increase the volume by turning the VOLUME knob. * Confirm the SPEAKER A/B buttons are set according to the speaker terminal connections. * Deactivate the ATT muting function by pressing the ATT button or adjusting the volume if “ATT” is displayed. * Readjust the volume if the protection circuit has muted it automatically. * If an error message appears, set the ID number correctly.
C
Cameron RamirezAug 1, 2025
How to fix a Marantz PM-11S2 Amplifier when no power is supplied?
- A
  Andrew OwenAug 1, 2025
  If your Marantz Amplifier isn't receiving power: * First, check the power cord connection to ensure it's properly connected. * If the OPERATE indicator is flashing, the protection circuit may be activated. Turn the power OFF, wait for at least 1 minute, and then turn it back ON.
C
cjacksonAug 6, 2025
Why is there noise or no sound when playing records on my Marantz PM-11S2 Amplifier?
- M
  Michelle HunterAug 6, 2025
  If you're experiencing noise or no sound when playing records on your Marantz Amplifier, consider the following: * Check the connections to the PHONO GND terminal to ensure proper grounding. * Verify the PHONO input terminal connection is complete. * Ensure that devices like TVs are not placed too close to the record player, as they may interfere with the sound. * Confirm the PHONO MC button on the front panel is correctly set for the type of cartridge you are using.
A
Anita HutchinsonAug 10, 2025
Why does sound only come from one speaker or the volume differs in my Marantz Amplifier?
- W
  William GrantAug 10, 2025
  If sound is only coming from one speaker or the volume levels differ between the left and right speakers on your Marantz Amplifier: * Check the speaker cable connections to ensure they are properly connected. * Verify that the volume (LEVEL TRIM) and sound quality (BASS/TREBLE) settings are the same for both the left and right channels. If they are different, perform trimming again.
M
Mrs. Courtney SotoAug 14, 2025
How to stop howling when increasing volume during record playing on Marantz PM-11S2 Amplifier?
- M
  Molly LeeAug 15, 2025
  If you experience howling when increasing the volume while playing records on your Marantz Amplifier: * Try to place the speakers as far away from the record player as possible. * If the record player is on a rack or floor prone to vibration, use an insulating pad. If one wasn't supplied with the record player, you can purchase one.
E
emily11Aug 19, 2025
What causes reversed left and right channels on my Marantz PM-11S2 Amplifier?
- L
  lori24Aug 19, 2025
  If the left and right channels are reversed on your Marantz Amplifier, the likely cause is that the left and right speaker cables or input cables are connected incorrectly. Ensure that you make these connections properly.
J
Jenna GarciaAug 23, 2025
Why is my Marantz Amplifier outputting monaural sound?
- B
  Brandon HensonAug 23, 2025
  If your Marantz Amplifier is outputting monaural sound, it might be because the MODE switch on the rear panel is set to “BI-AMP”. To fix this, turn the unit off, set the MODE switch to STEREO, and then turn the unit back on.