How to troubleshoot a completely dead Martin MAC 101 fixture?
If your Martin Lighting Equipment fixture is completely dead, the issue is likely due to one of two reasons: * There is no power to the fixture. Check the AC mains power and connections to ensure the fixture is receiving power. * There is an internal circuit fault. In this case, you should have the fixture serviced by a Martin service technician.
Why does Martin MAC 101 light output shut down unexpectedly?
If the light output of your Martin Lighting Equipment shuts down unexpectedly, it's likely because the fixture is overheating. To resolve this: * Clean the fixture, paying special attention to the air vents. * Ensure there is free airflow around the fixture. * Verify that the ambient temperature does not exceed the maximum permitted level. * Switch to FULL cooling mode. If the problem persists after these steps, contact Martin for further advice.
What to do if Martin Flood Light responds erratically to the controller?
If Martin Flood Light fixtures respond erratically, inspect data link connections and cables, correcting poor connections and replacing damaged cables. Ensure the data link is terminated by inserting a termination plug in the output connector of the last fixture. Check the fixture's DMX addressing and mode against the controller's settings. Bypass fixtures one at a time to identify any defective units disturbing data transmission. If the XLR pin-out doesn't match, install a phase-reversing cable or swap pins 2 and 3 in the erratic fixture.
How to troubleshoot if Martin Flood Light is completely dead?
If your Martin Flood Light is completely dead, first check the AC mains power and connections to ensure the fixture is receiving power. If the power supply is OK, the issue might be an internal circuit fault, so have the fixture serviced by a Martin service technician.
Why does Martin Flood Light output shut down unexpectedly?
If the light output of your Martin Flood Light shuts down unexpectedly, it might be overheating. Clean the fixture, especially the air vents, and ensure free airflow around it. Make sure the ambient temperature doesn't exceed the permitted level and switch to FULL cooling mode. If the problem continues, contact Martin for advice.
How to troubleshoot a completely dead Martin Moving light fixture?
If your Martin Moving light fixture is completely dead, start by checking the AC mains power and connections. If the power supply is ok, there may be an internal circuit fault. In this case, have the faulty fixture serviced by a Martin service technician.
Why does the light output shut down unexpectedly on my Martin Moving light fixture?
If the light output of your Martin Moving light fixture shuts down unexpectedly, the fixture may be overheating. Clean the fixture, paying special attention to the air vents. Ensure there is free airflow around the fixture and verify that the ambient temperature does not exceed the maximum permitted level. You can also switch to FULL cooling mode. If the problem persists, contact Martin for advice.
What to do if Martin MAC 101 Lighting Equipment responds erratically to the controller?
If your Martin Lighting Equipment fixture responds erratically or not at all to the controller, even after resetting, it may be due to several reasons: * There could be a fault on the data link. Inspect the connections and cables, correct any poor connections, and repair or replace damaged cables. * The data link may not be terminated. Insert a termination plug in the output connector of the last fixture on the link. * The fixture DMX addressing might be incorrect. Check the addressing on both the fixture and the controller, and ensure the fixture is set to the correct DMX mode. * A defective fixture could be disturbing data transmission. Bypass one fixture at a time by unplugging the XLR in and out connectors and connecting them directly together until normal operation is regaine...
All dimensions are in millimeters.
Details safety measures for electrical hazards.
Outlines precautions to prevent fire and burn injuries.
Covers safety guidelines to prevent physical harm.
Illustrates and labels the main parts of the fixture.
Provides initial setup and safety checks before powering on.
Specifies voltage, frequency, cable specs, and plug installation.
Step-by-step guide for attaching power connectors and relaying power.
Tips for reliable data transmission and connecting the data link.
Instructions for placing, mounting on truss, and hanging the fixture.
Information on using special brackets for fast mounting.
Using controls, setting DMX address, and selecting DMX modes.
Adjusting speed, cooling, and dimming curves for desired output.
Procedure to revert all settings to their original factory state.
Controlling pan, tilt, shutter effects, and light intensity via DMX.
Managing color mixing, wheel effects, and CTC for RGB models.
Adjusting color temperature for warm/cold white mixing.
Controlling intensity of warm or cold white LEDs.
Guidelines for cleaning the fixture to maintain performance.
Using onboard menus for diagnostic tests and pan/tilt calibration.
Viewing live DMX, firmware, temperatures, and operational hours.
Instructions for installing optional diffuser filters and top hats.
Detailed channel mapping for RGB model control.
Detailed channel mapping for CT model control.
Detailed channel mapping for CLD and WRM model control.
Mapping of LEE color numbers to RGB values for the color wheel.
List of messages, their causes, and recommended actions.
Guide to diagnosing and resolving operational issues.
Dimensions, effects, optics, and LED lifetime details.
DMX channels, power, and thermal data.
Mounting, electrical, thermal, and regulatory information.
List of optional accessories and product ordering information.
Information on proper recycling and disposal of the product.
General| Type | Moving Head |
|---|---|
| Light Source | LED |
| Color Mixing | RGB |
| Control Protocol | DMX-512 |
| Source | LED |
| Pan | 540° |
| Tilt | 270° |
| Zoom range | Fixed |
| Power Requirements | 100-240 V AC, 50/60 Hz |
To Next Page