Masport Monaco - Remote Control and ECS Operation

•Checkthedisplayontheremotecontrol.Ifitreads‘OFF’,aimtheremotecontroltowardthereceiver
andpressthecentrebuttonontheremotetoswitchitto‘ON’.
Whenthedisplayshows‘ON’,theSETTEMPwillbedisplayedbelowtheROOMTEMP.Forthe
burnertolight,theSETTEMPmustbehigherthantheROOMTEMP.Raise theSETTEMP,if
necessary,bypressingtherighthandbutton.
•TurnthePILOTcontrolfullyanticlockwisetothe‘ON’positionandthefirewilllightatfullheat.
Theremaybeastrongsmellthefirsttimethelogsarefiredbutthiswillsoondisappear.
•Aftertenminutes,settheHI-LOcontroltogivethedesiredheatoutput.
•Atthisstageyoumayturnonthefanbyrotatingthefanswitchineitherdirection.Theswitchgives
threespeedsandhasan‘OFF’position.NOTE.Thefanisalsocontrolledbyaninternalswitchwhich
willnotpermitittostartuntilthefireishot(abouttenminutesfromcoldonhighfire)andwillkeepit
runningforsometimeafterthefiregoesout.
PROGRAMMINGTHEREMOTECONTROL
Thecontrolcanbeprogrammedtooperatetheheateratadesiredlatertime.Thecontrolsforthisare
under the sliding cover below the display. Programming instructions are in the instruction sheet
suppliedwiththeremotecontrol.
ECSMODELS:-
Thesehavearemotecontrolhandpieceandthermostatconnectingterminalsontherearoftheheater.
Ifthewallthermostatisnotfitted,asmallwirebridgingloopmustbefittedacrosstheseterminalsor
the heater will not light. If the battery operated wall thermostat is fitted, it must be switched to
‘HEAT’(under the bottom hingedcover)and the SET temperature must be above the prevailing
ROOMtemperaturebeforetheheaterwilllight.TheSETtemperaturecanbealteredbypressingthe+
and–buttonsalongsidethe display.Ifthereisnodisplay,checkthethermostat batteries(3xAA
alkaline).
• Toavoidtheriskofbackburning,donotattempttore-lightthefirelessthanthreeminutesafterithas
beenextinguished.
•Checkthatthepowerswitchatthewallis‘ON’andpressthetoproundhandpiecebuttonwhileaiming
thehandpiecetowardthereceiverontherightfrontcornerofthepedestalfoot.Theredindicatorlight
onthehandpieceshouldlightandtheredindicatorlightalongsidethereceiver(onthepedestalfoot)
should light inresponse andremainalight after thehandpiece buttonis released. If the handpiece
indicatordoesnotlightup,checkthehandpiecebatteries(4xAAAcells).Ifthereceiverindicatordoes
notlight,pressthesmallbuttonalongsidethereceiver(onthepedestalfoot).Ifthereceiverindicator
stilldoesnotlight,pressthered‘RESET’buttononthebackoftheheaterandtryagain.
•Assoonasthereceiverindicatorlights,athirtysecondignitionsequence begins.Afteraboutthree
secondsfromthestart,therewillbeacontinuoussparkatthepilotelectrodewhichwilllightthepilot.
Whenstartingforthefirsttime,therewillprobablybeairinthepilotlinesupplypipe,soignitionmay
notoccurimmediately.Ifithasnotlitwithinaboutthirtyseconds,thesparkwillcease.Inthisevent,
presstheredRESETbuttononthebackoftheheaterandtrylightingagain.Ifyouneedtopressthe
resetagain,waitatleasttensecondsbeforedoingthis.Ifthereisalotofairinthepipeline,itmaybe
necessarytorepeatthisresetprocedureseveraltimes.
•Whenthepilotlights,theECSsystemshutsdowntheignitionsparkandthenturnsonthegassupply
tothemainburner.Thiswilligniteshortlyafter.
•Oncethemainburnerisalight,thesizeoftheflamecanbeadjustedusingthetoprockerswitchonthe
handpiece.Pressing+increasestheflame.Notethattheresponsetoflameadjustmentmaytakeabout
twentyseconds,sotherockerswitchshouldbehelddownuntiltheflamereachesthedesiredheight.
•Whiletheheaterisbeingswitchedonandoffbythewallthermostat(iffitted),theredindicatorlight
besidethereceiverwillremainalight,showingthattheheaterisreadytolightagainwhentheroom
temperaturefalls.Theflamewilllightatitslastheightsetting.Thepilotlightextinguisheseachtime
theflameextinguishes.
•Ifthemainssupplytotheheaterisswitchedoff,thefirewilllightnexttimeattheLOWflamesetting,
butifthemainssupplyisuninterrupted,theflamewilllightagainatitslastsetting.
3