32 M32 DIGITAL CONSOLE User Manual
eects
The LIBRARY screen’s eects tab allows you to load and save presets for the
various onboard eects processors.
To adjust the various settings on the eects tab, perform the following steps:
1. Adjust the rst push encoder to select which of the eight eects slots to load
or save a preset.
• As you navigate among the eight eects slots the specic eect
processor loaded into each slot will display on the screen as both a
name and an icon.
2. To save and load presets, as well as import/export them, follow the same
procedure as detailed in the LIBRARY screen channel tab.
routing
The LIBRARY screen’s routing tab allows you to load and save presets of the
M32’s signal routings. This can be useful for repeating specic routing scenarios
that occur over and over on a regular basis, such as when using the console for a
weekly club gig or worship service.
To adjust the various settings on the routing tab, perform the following steps:
1. Adjust the rst push encoder to select which specic console signal paths
will be recalled when loading a routing preset. Choices include:
• Channel Inputs
• Analog Out
• Auxiliary Out
• P16 (Ultranet) Out
• Card Out
• AES50 Out.
2. Tap the rst encoder to turn the currently selected element on or o in the
recall list.
3. To save and load presets, as well as import/export them, follow the same
procedure as detailed in the LIBRARY screen channel tab.
2.6 Eects
The EFFECTS screen controls various aspects of the eight internal eects
processors. On this screen the user can select specic types of eects for the
eight internal processors, congure their input and output paths, monitor their
levels, and adjust the various eect parameters.
The rst four slots can be Insert and Side-Chain eects, and the slots ve to eight
are Insert only. Additionally these slots can only hold some eects excluding
reverbs and other power-intensive eects. They also have dierent selections for
the input sources.
The EFFECTS screen contains the following separate tabs:
home: The home tab provides a general overview for all eight eects
processors, displaying what eect has been inserted in each of the eight
slots, as well as displaying input/output paths for each slot, and the I/O
signal levels.
fx1-8: These eight duplicate screens display all relevant data for the right
separate eects processors, allowing the user to adjust all parameters for
the selected eect.
home
The EFFECTS screen’s home tab provides a high-level overview of the eight
eects processor slots, giving the user at-a-glance feedback on the eects they
have assigned to the slots, the console source and destination for each processor,
and the input/output levels for each processor.
To make adjustments on the EFFECTS screen’s home tab, perform the
followingsteps:
1. Adjust the rst push encoder to select the input source for the currently
highlighted eects block. Signal path choices include:
• Insert Send
• Mix Bus 1-16.
2. Tap the rst encoder to assign the currently selected input source.
3. Adjust the second encoder to select the input source for the right side of the
currently highlighted eects block.
4. Tap the second encoder to assign the currently selected input source.
TIP: To congure an eect as mono input and stereo output, set both input
sources to the same signal path
5. Tap the third and fourth encoders to mute the currently selected eect.
6. Adjust the fth encoder to scroll among the dierent audio eects available.
Choices include:
Hall Reverb Delay + Chamber M/S Fair Comp
Ambience Chorus + Chamber Dual Fair Comp
Rich Plate Reverb Flanger + Chamber Leisure Comp
Room Reverb Delay + Chorus Dual Leisure Comp
Chamber Reverb Delay + Flanger Ultimo Comp
Plate Reverb Modulation Delay Dual Ultimo Comp
Vintage Reverb Dual Graphic EQ Dual Enhancer
Vintage Room Stereo Graphic EQ Stereo Enhancer
Gated Reverb Dual TruEQ Dual Exciter
Reverse Reverb Stereo TruEQ Stereo Exciter
Stereo Delay Dual DeEsser Stereo Imager
Triple Delay Stereo DeEsser Edison EX1
Rhythm Delay Stereo Xtec EQ1 Sound Maxer
Stereo Chorus Dual Xtec EQ1 Dual Guitar Amp