Miller Fusion 185 User Manual

OM-284208 Page 15
F
Complete Parts List is available at www.MillerWelds.com
SECTION 3 – DEFINITIONS
3-1. Additional Safety Symbol Definitions
F
Some symbols are found only on CE products.
Warning! Watch Out! There are possible hazards as shown by the
symbols.
OM-
Become trained and read the instructions before working on the
machine or heating.
Safe85 2012 06
Connect green or green/yellow grounding conductor to ground
terminal.
Connect input conductors (L1, L2 And L3) to line terminals.
Safe86 2012 06
Never use generator inside a home or garage, even if doors and win-
dows are open.
Safe87 2012 07
Only use generator outside and far away from windows, doors, and
vents.
Safe88 2012 07
Do not use ether or other starting fluids. Using starting fluids voids warranty. See engine Owner’s Manual.
Safe89 2017 04
Hot muffler and exhaust pipe can cause severe burns.
Safe90 2017 04
Welding, cutting, drilling, or grinding on base can cause fire or explosion.
Safe91 2017 04
Do not spray water on CST units.
Safe92 2017 04
Door must be fully open during operation.
Safe93 2012 08
Drive rolls can injure fingers. Welding wire and drive parts are at welding voltage during operation keep hands
and metal objects away.
Safe95 2012 05
Never use generator inside a home or garage, even if doors and win-
dows are open.
OM-
Become trained and read the instructions before working on the
machine or heating.
Safe85 2012 06
Connect green or green/yellow grounding conductor to ground
terminal.
Connect input conductors (L1, L2 And L3) to line terminals.
Safe86 2012 06
Never use generator inside a home or garage, even if doors and win-
dows are open.
Safe87 2012 07
Only use generator outside and far away from windows, doors, and
vents.
Safe88 2012 07
Do not use ether or other starting fluids. Using starting fluids voids warranty. See engine Owner’s Manual.
Safe89 2017 04
Hot muffler and exhaust pipe can cause severe burns.
Safe90 2017 04
Welding, cutting, drilling, or grinding on base can cause fire or explosion.
Safe91 2017 04
Do not spray water on CST units.
Safe92 2017 04
Door must be fully open during operation.
Safe93 2012 08
Drive rolls can injure fingers. Welding wire and drive parts are at welding voltage during operation keep hands
and metal objects away.
Safe95 2012 05
Only use generator outside and far away from windows, doors, and
vents.
3-2. Miscellaneous Symbol Definitions
Amperage
Voltage
Rated No-Load Volt-
age (OCV)
Conventional Load
Voltage
Rated Welding
Current
Duty Cycle
Negative
Positive
Direct Current (DC)
Alternating Current
(AC)
Protective Earth
(Ground)
Circuit Breaker
Supplementary
Protector
Read Operator’s
Manual
Shielded Metal Arc
Welding (SMAW)
Fuel
Fuel Shutoff
Engine Oil
Engine Choke
Air Filter
Engine
Engine
Engine RPM
Engine Stop
Engine Start
Idle (Slow)
Run (Fast)
Temperature
 A complete Parts List is available at www.MillerWelds.com
OM-285986 Page 9
SECTION 3 DEFINITIONS
3-1. Miscellaneous Symbols And Definitions
A
Amperage
V
Voltage
On
Off
Remote
Voltage Input
Line Connection
Three Phase
Negative
Foot Control
Single Phase
Positive
Gas Tungsten Arc
Welding
%
Percent
Increase
Output
Shielded Metal
Arc Welding
(SMAW)
Lift-Arc Operation
(GTAW)
Pulsed
Notes
Increase
Rated Supply
Voltage
Rated Load Speed
Rated No-Load
Speed
Rated Idle Speed
Rated Maximum
Supply Current

Miller Fusion 185 Specifications

General

Brand	Miller
Model	Fusion 185
Category	Portable Generator
Language	English