Miller Millermatic 251 Technical Manual

Miller Millermatic 251

72 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Processes

Description

MIG (GMAW) Welding

Flux Cored (FCAW) Welding

Arc Welding Power Source

and Wire Feeder

TM-1326B 2006−10

Eff. w/Serial Number LB170597

Millermatic 251

R

Visit our website at

www.MillerWelds.com

File: MIG (GMAW)

Table of Contents

Other manuals for Miller Millermatic 251

Owner's Manual56 pages

Questions and Answers:

O
odyerAug 21, 2025
How to troubleshoot Miller Welding System when there is no weld output and wire does not feed?
- M
  Mark BakerAug 21, 2025
  To troubleshoot a Miller Welding System with no weld output and the wire not feeding, ensure the line disconnect switch is On. Also, replace the building line fuse or reset the circuit breaker if it's open. Secure the gun trigger connections. If HL.P 001 appears, turn the power switch off and on; if the message persists, have a Factory Authorized Service Agent check the unit. If Thermistor T detects overheating, wait for the unit to cool. If HL.P 004 appears, release the trigger or remove any stuck wire causing a short circuit. If the message remains, have an agent check for shorted trigger leads. Finally, have an agent check the power switch and all board connections.
C
Carmen AndersonAug 22, 2025
What to do if my Miller Millermatic 251 Welding System has no wire feed?
- K
  Karen JohnsonAug 23, 2025
  To troubleshoot a Miller Welding System with no wire feed, first turn the Wire Speed control to a higher setting. Clear any obstruction in the gun contact tip or liner. Readjust the drive roll pressure and change to the correct size drive rolls. Rethread the welding wire. If Thermistor T detects overheating, allow the unit to cool. If HL.P 004 appears, reset the message by releasing the trigger or removing any stuck wire causing a short circuit. Check the wire feed delivery system, gun trigger, and leads, repairing or replacing the gun if necessary. If problems persist, have a Factory Authorized Service Agent check the main control board.
J
jonesdeannaAug 25, 2025
What to do if Miller Millermatic 251 has no weld output but wire feeds?
- M
  Megan ClarkAug 25, 2025
  If your Miller Welding System has no weld output but the wire feeds, ensure the work clamp is connected for good metal-to-metal contact. Replace the contact tip. If HL.P 003 appears on the meters, have a Factory Authorized Service Agent check the main control board and main rectifier.
A
Amy ManningAug 26, 2025
Why is there low weld output on my Miller Welding System?
- M
  Martin LawrenceAug 26, 2025
  To address low weld output on your Miller Welding System, first connect the unit to the correct input voltage or check for low line voltage. Also, check the input voltage jumper links and correct their position if necessary. If the issue persists, have a Factory Authorized Service Agent check the main control board.
K
Katie MoodyAug 27, 2025
Why is the wire speed low, high, or erratic on my Miller Welding System?
- C
  Charles CabreraAug 28, 2025
  To resolve low, high, or erratic wire speed on your Miller Welding System, readjust the front panel settings. Change to the correct size drive rolls and readjust the drive roll pressure. If necessary, replace the inlet guide, contact tip, or liner. Check the position of the input jumper links. If problems persist, have a Factory Authorized Service Agent check the main control board.
B
Bryan LozanoAug 29, 2025
What to do if Miller Welding System has low, high, or erratic wire speed?
- D
  David CabreraAug 29, 2025
  Try readjusting the front panel settings. Ensure you are using the correct size drive rolls and readjust the drive roll pressure. Replace the inlet guide, contact tip, and/or liner if necessary. Check the position of the input jumper links. If the issue persists, have a Factory Authorized Service Agent check the main control board.
B
brandonjamesAug 31, 2025
Why does Miller Welding System have low weld output?
- K
  Kenneth JohnstonAug 31, 2025
  Ensure the unit is connected to the proper input voltage, and check for low line voltage. Also, check the input voltage jumper links and correct their position if necessary. If the issue persists, have a Factory Authorized Service Agent check the main control board.
C
Cesar WashingtonSep 2, 2025
How to fix low, high, or erratic wire speed on a Miller Welding System?
- L
  Laura MillerSep 2, 2025
  If you're experiencing low, high, or erratic wire speed on your Miller Welding System, start by readjusting the front panel settings. Change to the correct size drive rolls and readjust the drive roll pressure. Replace the inlet guide, contact tip, and/or liner if necessary. Check the position of the input voltage jumper links. Inspect the main control board PC1 and its connections, replacing if necessary. Finally, check the hub tension setting.
J
John NixonSep 3, 2025
What causes improper or no gas flow in my Miller Welding System?
- C
  Cassidy CostaSep 3, 2025
  If your Miller Welding System has improper or no gas flow, begin by cleaning or replacing the gas hose. Clear any blockage in the gun. If the gas flow is excessive, replace the regulator. Check the coil voltage and connections of the gas valve GS1, and verify the continuity of the coil, replacing GS1 if necessary. Check the main control board PC1 and connections, and replace if necessary.
J
John RodriguezSep 8, 2025
What to do if HL.P 004 appears on the meters of my Miller Welding System?
- J
  John MartinSep 8, 2025
  If the Miller Welding System shows 'HL.P 004' on the meters, try releasing the trigger or removing any stuck wire that might be causing a short circuit to reset the message. If the problem continues, it is recommended to have a Factory Authorized Service Agent check for shorted trigger leads or shorted contacts in the Reed Relay.

Miller Millermatic 251 Specifications

General

Input Phase	1-Phase
Input Frequency	60 Hz
Output Amperage Range	30 - 250 A
Welding Process	MIG
Rated Output	250 A
Wire Feed Speed	50 - 700 IPM
Input Voltage	208/230/460 VAC

Related product manuals

Miller Millermatic 250

Preview: Miller Millermatic 252

Miller Millermatic 252

Preview: Miller Millermatic 250X

Miller Millermatic 250X

Preview: Miller Millermatic 211

Miller Millermatic 211

Preview: Miller Millermatic 212 Auto-Set

Miller Millermatic 212 Auto-Set

Preview: Miller Millermatic 211 Auto-Set

Miller Millermatic 211 Auto-Set

Preview: Miller Millermatic 35

Miller Millermatic 35

Preview: Miller Millermatic 300

Miller Millermatic 300

Preview: Miller MILLERMATIC 135

Miller MILLERMATIC 135

Preview: Miller MILLERMATIC DVI

Miller MILLERMATIC DVI

Preview: Miller Millermatic 141

Miller Millermatic 141

Miller millermatic 180 auto-set